background image

G

RASS

 T

RIMMER

/B

RUSH

 C

UTTER

O

PERATOR

'

S

 M

ANUAL

9

1.

POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter.

2.

GRIP - Rear (right hand) handle.

3.

THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. Operation of the throttle trigger is

prevented unless throttle trigger lockout lever is engaged.

4.

STOP SWITCH - "SLIDE SWITCH" mounted on top of the Throttle Trigger Housing.  Move switch FORWARD to

RUN, BACK to STOP.

5.

FRONT HANDLE - The Front (loop) handle is loosely assembled to the Drive Shaft assembly and must be posi-

tioned for proper cutting attitude and operator comfort.

6.

DRIVE SHAFT ASSEMBLY - Includes the Rear (right hand) Handle assembly, Gear Housing assembly, Front (loop,

left hand) Handle assembly, steel drive shaft and Safety Decal.

7.

NYLON CUTTER HEAD - Contains replaceable nylon trimming line that advances when the trimmer head is tapped

against the ground while the head is turning at normal operating speed.

8.

CUT-OFF KNIFE - Automatically trims line to the correct length: 5" after head is tapped on the ground. If trimmer is

operated without a cut-off knife the line will become too long, the engine will overheat and engine damage may occur.

9.

PLASTIC DEBRIS SHIELD ASSEMBLY - Included in plastic bag (co-pack).   MUST be installed on unit before use,

see Assembly Instructions.  Shield assembly includes the Cut-Off Knife. Mounts on the Gear Housing Assembly just

above the cutting attachment. Helps protect the operator by deflecting debris produced during the trimming opera-

tion.  This shield must be replaced with the steel shield for blade use.

10. THROTTLE TRIGGER - Spring loaded to return to idle when released.  During acceleration, press trigger gradually

for best operating technique.

11. SPARK PLUG - Provides spark to ignite fuel mixture.

12. TOP GUARD - Protects arm from the hot engine.

13. SPARK ARRESTOR - CATALYTIC MUFFLER / MUFFLER -The muffler or catalytic muffler controls exhaust noise

and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep

exhaust area clear of flammable debris.

14. FUEL TANK - Contains fuel and fuel filter.

15. RECOIL STARTER HANDLE - Pull handle slowly until starter engages, then quickly and firmly.  When engine

starts, return handle slowly.  DO NOT let handle snap back or damage to unit will occur.

16. FUEL TANK CAP - Covers and seals fuel tank opening.

17. PRIMER BULB - Pumping primer bulb before starting engine draws fresh fuel from the fuel tank priming the carbure-

tor for starting.  Pump primer bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an

additional 4 or 5 times.

18. AIR CLEANER - Contains replaceable filter element.

19. CHOKE - The choke control is located on the top of the air filter case.  Move choke lever  to "Cold Start" (

) to

close choke for cold start. Move choke lever to "Run" (

) position to open choke.

20. SAFETY VIDEO - (Not included with unit) P/N 99922202540 English version and P/N 99922203508 Spanish version

are  available at a cost of $5.00 from ECHO, INC. or any authorized ECHO dealer. The video overviews safety precau-
tions and proper operating techniques and is supplemental to the Safety Manual. Read and understand the Safety

Manual for complete information on safe operation.

Содержание SRM-230 - 11-03 SERIAL NUMBER...





























Отзывы: