Echo SHC-266 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 36

background image

30

X7502026702

© 4/2013 ECHO Inc.

STORAGE

SHC-266

STORAGE

The muffler and surrounding cover become hot during operation. Always keep exhaust area clear of
flammable debris during transportation or when storing, otherwise serious property damage or
personal injury may result.

Long Term Storage (Over 30 Days)

Do not store your unit for a prolonged period of time (30 days or longer) without performing protective
storage maintenance which includes the following:

1. Store unit in a dry, dust free place, out of the reach of children.

Hedge Clipper blades are very sharp. Touching them may lead to severe personal injury. Avoid
touching blades whenever possible, and always wear gloves to protect hands.

Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark,
otherwise serious personal injury may result.

2. Place the stop switch in the “STOP” position.

3. Remove accumulation of grease, oil, dirt and debris from exterior of unit.

4. Perform all periodic lubrication and services that are required.

5. Apply clean oil to the entire length of the blade. Be certain the blade bolts are lubricated.

6. Install blade cover on blades.

7. Tighten all the screws and nuts.

8. Drain fuel tank completely. Press purge bulb 6 -7 times to remove remaining fuel from carburetor then

drain the tank again. Close choke, start and run the engine until it stops due to lack of fuel.

9. Allow the engine to cool, then emove the spark plug and pour 7 cc (1/4 oz.) of fresh, clean, two-stroke

engine oil into the cylinder through the spark plug hole.

a. Place a clean cloth over the spark plug hole.

b. Pull the recoil starter handle 2-3 times to distribute the oil inside the engine.

c. Observe the piston location through the spark plug hole. Pull the recoil handle slowly until the piston

reaches the top of its travel and leave it there.

10. Install the spark plug (do not connect ignition cable).

Always store and transport hedge clippers in a stable, horizontal position. Support gear case and cutting
blades to prevent excessive flexing, which may cause damage to these components. Always install blade
cover when transporting or storing unit.

«
...
28
29
30
31
32
...
»

Содержание SHC-266





































Отзывы:

Нет отзывов

Похожие инструкции для SHC-266

Бренд: Makerfire Страницы: 10

Бренд: B&K Страницы: 16

Бренд: Quick Страницы: 24

Бренд: JDS Uniphase Страницы: 144

IP Video Test Option HST-3000

Бренд: JDS Uniphase Страницы: 14

Бренд: Mackie Страницы: 7

Бренд: Uchida Yoko Страницы: 40

Бренд: Teagle Страницы: 2

FUSION APOLLO MS-WB675

Бренд: Garmin Страницы: 18

Бренд: Rapid Shape Страницы: 12

Бренд: Ignis Pixel Страницы: 4

Deep Root Planter 1.8m

Бренд: Zest 4 Leisure Страницы: 5

Бренд: Faro Страницы: 161

Бренд: FISBA Страницы: 16

Бренд: Facom Страницы: 130

Бренд: Korg Страницы: 287

Бренд: Laserworld Страницы: 18

GENTLEsilence 8000BN

Бренд: KaVo Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды