background image

16

D

A

A

C

STARTING

 

WARM

 

ENGINE

The starting procedure is the same as Cold Start except DO NOT close
the choke, and do not depress throttle trigger to wide open position.

WARNING     

     DANGER

The attachment should not move at idle, otherwise serious
personal injury may result.

NOTE
If attachment moves, readjust carburetor according to “Carburetor
Adjustment” instructions in this manual or see your ECHO Dealer.

1.

Stop Switch
Move stop switch button  (A) away from the STOP position.

2.

Primer
Pump primer bulb (C) until fuel is visible and flows freely in the
clear fuel tank return line. Pump bulb an additional 4 or 5 times.

3.

Recoil Starter
Lay the unit on a flat area and keep movable attachment parts clear
of all obstacles. Rapidly pull recoil starter handle/rope (D) until
engine fires.

NOTE
If engine does not start after 5 pulls, use Cold Start Procedure.

STOPPING

 

ENGINE

1.

Throttle
Release throttle and allow engine to return to idle before shutting
off engine.

2.

Stop Switch
Move stop switch button (A) backward to STOP position.

WARNING     

     DANGER

If engine does not stop when stop switch is moved to STOP
position, close choke - COLD START position - to stall engine.
Have your ECHO dealer repair stop switch before using shaft
hedge clipper again.

Содержание SHC-260





























Отзывы: