Echo PPT-2620H Скачать руководство пользователя страница 51

Страница: 51 / 56

PPT-2620 / H

SPECIFICATIONS

X7502346700

SPECIFICATIONS

Model

PPT-2620

PPT-2620H

Length (standard)

2,716 mm (107 in.)

Length (Extended)

3,704 mm (146 in.)

Width

273 mm (11 in.)

Height

260 mm (10 in.)

Weight (dry)

7.9 kg (17.4 lb.)

7.7 kg (17 lb.)

Engine Type

Air-cooled, two-stroke, single cylinder gasoline
engine

Bore

34 mm (1.34 in.)

Stroke

28 mm (1.1 in.)

Displacement

25.4 cc (1.55 in.

)

Exhaust

Spark arrester muffler or spark arrester muffler with
catalyst

Carburetor

Diaphragm with purge pump

Ignition System

Flywheel magneto, capacitor discharge ignition type

Spark Plug

NGK CMR7H
Gap 0.65 mm (0.026 in.)

Fuel

Mixed (gasoline and two-stroke oil)

Fuel/Oil Ratio

50:1

Gasoline

Use 89 Octane unleaded. Do not use fuel containing
methyl alcohol, more than 10% ethyl alcohol or 15%
MTBE. Do not use alternative fuels such as E15 or
E85.

Oil

ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345- FD,
two-stroke, air-cooled engine oil.

Fuel Tank
Capacity

0.53 L (17.9 US fl. oz.)

Starter System

Automatic rewind starter

Clutch

Centrifugal type

Drive Shaft

Aluminum extrusion

Sprocket Type

6 tooth spur, 9.53 mm (3/8 inch) pitch

Gear Case Ratio

1.5:1

Oiling System

Automatic

Содержание PPT-2620H

























































Результаты поиска

Содержание PPT-2620H

Отзывы:

Похожие инструкции для PPT-2620H

Бренды по названию

Популярные бренды

Echo PPT-2620H, Руководство оператора

Результаты поиска

Содержание PPT-2620H

Отзывы:

Похожие инструкции для PPT-2620H

Бренды по названию

Популярные бренды