Echo Power Pruner PPT-2100 Скачать руководство пользователя страница 40

Страница: 40 / 40

OWER

RUNER

PERATOR

ANUAL

29A

GUIDE

BAR

AND

SAW

CHAIN

REPLACEMENT

WARNING DANGER

Never try to replace or adjust guide bar and saw chain with engine running. This saw chain is VERY sharp, wear
heavy gloves to protect your hands when handling it. Wear eye protection meeting CE or ANSI Z87.1 specification.

Guide Bar Replacement / Installation

Level 3

Tools required: 10mm (13/32 in.) Socket, Screwdriver

•

Loosen two (2) 10mm (13/32 in.) guide bar nuts (A) and relieve saw
chain tension turning screw (B) counter clockwise.

•

Remove sprocket cover.

•

Free saw chain from sprocket and remove from guide bar. If guide
bar is okay proceed to saw chain installation.

•

Slide guide bar forward and remove from cutting attachment. Install
new guide bar sliding it onto the cutting attachment as far as
possible.

•

Turn saw chain adjustment screw until adjusting pin (C) fits into
round hole in guide bar.

Saw Chain Installation

Level 3

•

Install new saw chain onto guide bar. Make sure cutting links are
faced towards the nose of the guide bar.

•

Engage saw chain with sprocket.

•

Replace sprocket cover and guide bar nuts.

•

Follow instruction on adjusting saw chain tension page 16.

Содержание Power Pruner PPT-2100









































Результаты поиска

Содержание Power Pruner PPT-2100

Отзывы:

Похожие инструкции для Power Pruner PPT-2100

Бренды по названию

Популярные бренды

Echo Power Pruner PPT-2100, Руководство оператора

Результаты поиска

Содержание Power Pruner PPT-2100

Отзывы:

Похожие инструкции для Power Pruner PPT-2100

Бренды по названию

Популярные бренды