Echo Power Pruner PPT-2100 Скачать руководство пользователя страница 37

Страница: 37 / 40

OWER

RUNER

PERATOR

ANUAL

15A

2. Loosen center clamp knob (F) turning counter clockwise.

3. Pull upper shaft tube (G) out of fiberglass lower shaft tube 127-152

mm (5-6 in.), then slide (G) back into fiberglass lower shaft tube
exposing inner power transmission shaft (H). Align and join star
shaped drive end of inner power transmission shaft (H) with cutting
attachment shaft (I).

4. Align ridges on upper shaft tube (G) with seams in cutting attach-

ment.

5. Slide together aligning locator screw (E) in cutting attachment with

locating hole (J) in upper shaft tube.

6. Tighten locator screw (E). Tighten four (4) cutting attachment

screws (D).

7. Extend upper shaft tube to desired length. Tighten center clamp

knob (F) turning clockwise.

THROTTLE

LINKAGE

INSTALLATION

NOTE
The engine is delivered separated from shaft tube. The throttle
linkage and stop switch wires are attached to the rear handle.

1. Loosen outer 10mm nut (E) on throttle linkage.

2. Insert throttle linkage in fan cover slot (A).

3. Finger tighten nut (E) and attach the inner linkage to the swivel (B)

on the carburetor throttle plate.

NOTE
It is important that the head of the throttle linkage fits inside the slot
well of the swivel (B).

Содержание Power Pruner PPT-2100









































Результаты поиска

Содержание Power Pruner PPT-2100

Отзывы:

Похожие инструкции для Power Pruner PPT-2100

Бренды по названию

Популярные бренды

Echo Power Pruner PPT-2100, Руководство оператора

Результаты поиска

Содержание Power Pruner PPT-2100

Отзывы:

Похожие инструкции для Power Pruner PPT-2100

Бренды по названию

Популярные бренды