background image

18

AIR

 

FILTER

Level 1.

Tools required:

Cleaning brush, 25 or 50 mm (1 or 2 in.) medium bristle
paint brush.

Parts required:

(PE-2000)  90008 REPOWER AIR & FUEL FILTER KIT
(PE-2400/3100)  90030 REPOWER AIR & FUEL
FILTER KIT

1.

Close choke (Cold Start Position). This prevents dirt from entering
the carburetor throat when the air filter is removed. Brush accumu-
lated dirt from the air cleaner area.

2.

Remove the air cleaner cover. Clean and inspect the element for
damage.  If element is fuel soaked and very dirty, replace.

3.

If element can be cleaned and reused, be certain it:
•still fits the cavity in the air cleaner cover.
•is installed with the original side out.

NOTE
Carburetor adjustment may be needed after air filter cleaning/
replacement. See Carburetor Adjustment Section.

FUEL

 

FILTER

Level 1.

Tools required:

Fuel line hook, 200-250 mm (8-10 in.) length of wire
with one end bent into a hook. Clean rag, funnel, and
an approved fuel container.

Parts required:

(PE-2000)  90008 REPOWER AIR & FUEL FILTER KIT
(PE-2400/3100)  90030 REPOWER AIR & FUEL
FILTER KIT

WARNING  

  DANGER

Fuel is VERY flammable. Use extreme care when mixing, storing or
handling.

1.

Use a clean rag to remove loose dirt from around fuel cap and empty
fuel tank.

2.

Use the “fuel line hook” to pull the fuel line and filter from the tank.

3.

Remove the filter from the line and install the new filter.

PE-2000

PE-2000

Содержание PE-2000 Type 1/1E





























Отзывы: