background image

14

O

PERATION

STARTING

 

COLD

 

ENGINE

NOTE
• 
Check unit for loose nuts, bolts and screws before starting.
• Always clear work area of debris before starting  operation.
• Always position the unit firmly on the ground before starting.
• When pulling recoil starter rope, use short pulls, 1/2 to 2/3 of

rope length.

• Do not allow the recoil starter handle to snap back against the

housing.

• Always hold the unit firmly.

WARNING    

     DANGER

When engine starts, the blade may rotate, even with throttle trigger in
idle (Release) position.

1.

Stop Switch
Move stop switch button  (A) away from the STOP position.

2.

Choke
Move choke (B) to "Cold Start" position.

3.

Primer Bulb
Pump primer bulb (C) until fuel is visible in the "Clear" fuel return
line. Pump bulb an additional 4 or 5 times.

WARNING     

    DANGER

Inspect starting area for hazards such as rocks, glass, debris etc.
which could be contacted by the cutting attachment when starting.
Keep helpers and bystanders at least 15 m  (50 ft.) from starting
area, otherwise serious personal injury may result.

4.

Recoil Starter
Lay trimmer on a flat, clear area. Firmly grasp throttle grip with left
hand and fully depress throttle trigger to wide open position.
Rapidly pull recoil starter handle/rope (D) until engine fires (or
maximum five [5] pulls).

5.

Choke
After engine fires (or five [5] pulls), move choke lever back to
"RUN" position. Hold throttle trigger fully depressed and pull
recoil starter handle/rope until engine starts and runs. Release
throttle trigger and allow unit to warn up at idle for several minutes.

NOTE
If engine does not start with choke in "RUN" position after 4 pulls,
repeat instructions.

6.

Throttle Trigger
After engine warm up, gradually depress throttle trigger to increase
engine RPM to operating speed.

PE-2000

PE-2400
PE-3100

A

A

PE-2000

C

B

D

PE-2400
PE-3100

B

C

D

Содержание PE-2000 Type 1/1E





























Отзывы: