background image

G

RASS

 T

RIMMER

O

PERATOR

'

S

 M

ANUAL

3

S

AFETY

DECALS

Locate these safety decals on  your unit. The complete unit illustration
found in the "DESCRIPTION" section,  will help you locate them.  Make
sure the decals are legible and that you understand and follow the
instructions on them.   If a decal cannot be read, a new one can be
ordered from your ECHO dealer.  See PARTS ORDERING instructions
for specific information.

M

ANUAL

S

AFETY

 S

YMBOLS

 

AND

 I

MPORTANT

 I

NFORMATION

Throughout this manual and on the product itself, you will find safety
alerts and helpful, informational messages preceded by symbols or key
words. The following is an explanation of those symbols and key words
and what they mean to you.

This symbol accompanied by the words WARNING
and DANGER calls attention to an act or condition that
can lead to serious personal injury to operator and
bystanders.

The circle with the slash symbol means whatever is
shown within the circle is prohibited.

IMPORTANT

The enclosed message

provides information necessary for the
protection of the unit.

NOTE

This enclosed message provides

tips for use, care and maintenance of the
unit.

Esta unidad puede ser peligrosa y producir
lesiones personales graves si no se usa en
forma adecuada. Para reducir el riesgo de
lesionarse, los operadores, los ayudantes y los
espectadores deben leer y comprender el
Manual Del Operador y los Manuales De
Seguridad que se entregan escritos en español.

ADVERTENCIA               PELIGRO

890228-09560

This unit can be dangerous and cause serious
injury if improperly used.  To reduce injury
risk to operator, helpers and bystanders, read
and understand the Operator's and Safety
Manuals, which are provided in Spanish.

WARNING          DANGER

ENGLISH TRANSLATION

SPANISH DECAL

P/N 89016006361

Hot Decal (near muffler)

IMPORTANT

NOTE

Содержание GT-200R - SERIAL NUMBER 07001001-07003100

























Отзывы: