background image

12

A

b

C

D

E

sTarTIng

 

Cold

 

engIne

  1. 

  

  Stop Switch 

                                                                       

   

Move stop switch button (A) away from the STOP position.

  2. 

Throttle Position Lever

    Move throttle position lever (B) midway between idle and full 

throttle positions.

 

3. 

Choke

    Move choke (C) to Cold Start (

) Position.

  4. 

Purge Bulb

      Pump purge bulb (D) until fuel is visible and flows freely in the 

clear fuel tank return line. Pump bulb an additional 4 or 5 times.

IMPORTANT  

Recoil starter:  Use short pulls - only 45 ~ 60 cm (18 ~ 24 in.) of 

rope for starting.  Do not allow the rope to snap back in.  Always 

hold the unit firmly.

  5. 

Recoil Starter

    Place the unit on a flat, clear area. Firmly grasp throttle grip with 

left hand and rapidly pull recoil starter handle/rope (E) until en-

gine fires (5 pulls maximum).

  6.

 

Choke

    After engine fires (or 5 pulls), move choke lever (C) to “Run”  

(

) position, then pull starter handle/rope until engine starts and 

runs. Allow unit to warm up at idle for several minutes.

  7.  After engine starts, move throttle lever to idle position, and allow 

unit to warm up for 3 minutes before use.

NOTE

If engine does not start with choke in “Run” position after 5 pulls, 

repeat instructions.

  8.    After engine warms up, depress throttle trigger or move throttle 

position lever gradually to increase engine RPM to operating 

speed.

Содержание ES-210 - 11-09

































Отзывы: