Echo CS-800P Скачать руководство пользователя страница 6

Страница: 6 / 36

CS-800P

NOMENCLATURE OF PARTS

* If a decal cannot be read, a new one can be

ordered from your ECHO dealer.

X524-004960

X505-002050

X505-006660

Part Number X505-006660

Part Number X524-004960

REPLACEMENT BAR AND CHAIN

REMPLACEMENT DU GUIDE ET DE LA CHAÎNE

GUIDE BAR P/NO.

CHAIN P/NO.

GUIDE PIÈCE NO.

CHAÎNE PIÈCE NO.

20” 20D0PS3870

72LPX70CQ

24” 24D0PS3881

72LPX81CQ

27” 27D0PS3893

72LPX93CQ

32” 32D0PS3805

72LPX105CQ

36” 36D0PS3816

72LPX116CQ

Note; There may be other replacement

components for achieving kickback

protection. For details, please refer

to the chain and bar combination

sheet shown in the operator’s manual.

REMARQUE; Il y peut y avoir d’autres composantes de

remplacement qui protègent en cas de rebondissement.

Pour plus de détails, se référer à la feuille

sur les combinaisons de guide et de chaîne

du manuel de l’utilisateur.

WARNING

Chain brake must be unlocked before removing or installing clutch

cover. Improper cover installation can result in serious injury and

cause severe damage to saw.
La frein du chaînes doit être désengagé avant d’enlever ou installer

la couverture d’embrayage. La couverture installée inexactement

peut avoir conséquence d’blessures serieuseset endommager la scie.

Part Number X505-002050

Содержание CS-800P





































Результаты поиска

Содержание CS-800P

Отзывы:

Бренды по названию

Популярные бренды

Echo CS-800P, Руководство оператора

Результаты поиска

Содержание CS-800P

Отзывы:

Бренды по названию

Популярные бренды