Echo CS-800P Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 36

Echo CS-800P Скачать руководство пользователя страница 14

14

CS-800P

EMISSION DATA

EMISSION CONTROL

(EXHAUST and EVAPORATIVE) EPA 2010 and/
or C.A.R.B. TIER III

The emission control system for the engine is EM/
TWC (Engine Modification and 3-way Catalyst)
and for the fuel tank the Control System is EVAP
(Evaporative Emissions) or N (for nylon tank).
Evaporative emission may be applicable to
California models only.

An Emission Control Label

is located on the

engine. (This is an example only, information on
label varies by engine family).

PRODUCT EMISSION DURABILITY
(EMISSION COMPLIANCE PERIOD)

The 300 hours emission compliance period is
the time span selected by the manufacturer
certifying the engine emissions output meets
applicable emissions regulations, provided that
approved maintenance procedures are followed
as listed in the Maintenance Section of this
manual.

EMISSION CONTROL INFORMATION

ENGINE FAMILY: #EHXS.0815RB DISPLACEMENT: 80.7 cc

EMISSION COMPLIANCE PERIOD: 300 Hours

THIS ENGINE MEETS U.S. EPA EXH/EVP EMISSION

REGULATIONS FOR MODEL YEAR * * * * REFER TO OWNER’S MANUAL

FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.

* * * ? ? ? ?

«
...
12
13
14
15
16
...
»

Содержание CS-800P





































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды