Echo CS-400F Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 36

background image

18

CS-400F

• Securely hold the chain saw as shown and pull

starter handle several times until first firing sound.

• Push choke control knob all the way in.

• Pull starter handle to start the engine.

Starter handle

Open choke

Choke control knob

NOTE

Do not increase engine speed while chain brake is

locked. Severe brake damage will result.

WHEN THE ENGINE IS WARM

CAUTION

Make sure the bar and chain are free from any

obstruction when starting the chain saw.

• Move chain brake lever fully forward to lock chain

brake before starting.

• Confirm there is fuel and chain oil in the tanks.

• Move ignition switch to “RUN” position.

• Securely hold the chain saw as shown and pull

starter handle.

• Choke may be used if necessary, but after first firing

sound, squeeze throttle trigger to release choke and

return engine to idle.

NOTE

If engine does not start after 5 pulls, use cold start

procedure.

Open choke

Choke control knob

Lock Chain

brake

NOTE

Do not increase engine speed while chain brake is

locked. Severe brake damage will result.

NOTE

If engine does not start after 5 pulls, repeat in-

structions.

CAUTION

•

After starting the engine, immediately squeeze

and then release throttle trigger to release fast

idle throttle latch, otherwise severe brake damage

may occur.

• Never use fast idle throttle latch for cutting.
• Use the fast idle throttle latch only in starting.

«
...
16
17
18
19
20
...
»

Содержание CS-400F





































Отзывы:

Нет отзывов

Похожие инструкции для CS-400F

Бренд: PAPILLON Страницы: 48

Бренд: Electrolux Страницы: 14

Бренд: Electrolux Страницы: 13

Бренд: Electrolux Страницы: 12

Бренд: Alpina Страницы: 18

Бренд: Dolmar Страницы: 68

Бренд: ST. SpA Страницы: 47

Бренд: Poulan Pro Страницы: 55

Бренд: Stiga Страницы: 20

Бренд: EMAK Страницы: 35

Бренд: SNOWJOE Страницы: 24

Power Tools RD-ECS20X

Бренд: Raider Страницы: 38

Бренд: Makita Страницы: 19

Бренд: Makita Страницы: 29

Бренд: McCulloch Страницы: 2

Бренд: McCulloch Страницы: 2

Бренд: McCulloch Страницы: 14

Бренд: McCulloch Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды