manualshive.com logo in svg

Echo CS-341, Инструкция по эксплуатации, Страница: 6 / 32

Поделиться
Скачать
Echo CS-341 Скачать руководство пользователя страница 6

6

e

mission

 D

ata

D

esCRiption

The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restric

-

tions, guide bar and saw chain installation and other assembly may be necessary.

After opening the carton, check for damage.  Immediately notify your retailer or ECHO Dealer of damaged or missing 

parts.  Use the contents list to check for missing parts.

Contents

  1  -  Power Head 

  1  -  Guide Bar

 *

1   -  Kick Guard

  1  -  Hex Head Bolt

  1  -  Hex Nut

 *

1  -  Saw Chain

  1  -  Instruction Manual

  1  -  Safety Manual

  1  -  Warranty Registration Card

  1  -  Assembly Tool (s)

  1  -  Echo Power BlendX 

TM

 2-stroke oil sample

* 

The machine may be delivered with guide bar and saw chain

 

assembled.

*

X7503206101

X750009891
11/08

  WARNING

Read rules for safe operation and instructions carefully. ECHO provides an Instruc-
tion Manual and a Safety  Manual. Both must be read and understood for proper and
safe operation.

Chain Saw

Instruction Manual

MODEL :

CS-341

An Emission Control Label 

is located on the engine.  (This 

is an EXAMPLE ONLY, information on label  varies by 

engine FAMILY).

e

mission

 C

ontRol

 (

exhaust

 

&

 

evapoRative

)

EPA 2010 and Later and/or C.A.R.B. TIER III 

PRODUCT  EMISSION  DURABILITY  (EMISSION COMPLIANCE PERIOD)

The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emis-

sions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as 

listed in the Maintenance Section of this manual.

The emission control system for the engine is EM (engine 

modification) and, if the second to last character of the Engine 

Family on the Emission Control Information label (sample 

below) is “C”, “K”, or “T”, the emission control system is EM 

and TWC (3-way catalyst). The fuel tank/fuel line emission 

control system is EVAP (evaporative emissions). Evaporative 

emissions for California models may only be applicable to fuel 

tanks.

Содержание CS-341

































Отзывы:

Нет отзывов