Echo CS-341 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 32

background image

20

muffleR

spaRk

aRRestoR

IMPORTANT

Carbon deposits in muffler will cause a drop in engine

output and overheating. Spark arrestor screen must be

checked periodically.

1. Remove muffler cover.

2. Remove spark arrestor screen cover, gaskets, and

screen from muffler body.

3. Clean carbon deposits from muffler components.

NOTE

When cleaning carbon deposits, be careful not to dam-

age the catalytic element inside muffler.

4. Replace screen if it is cracked, plugged, or has holes

burned through.

5. Assemble components in reverse order.

Cooling

system

Cleaning

• Remove spark plug lead.

• Remove two (2) muffler cover screws and muffler cover.

• Remove four (4) recoil starter housing screws and starter

housing.

• Use a stiff bristle cleaning brush (do not use a metal

brush) to remove dirt from cylinder fins in muffler and

ignition coil areas.

«
...
18
19
20
21
22
...
»

Содержание CS-341

































Отзывы:

Нет отзывов

Похожие инструкции для CS-341

Бренд: Feider Machines Страницы: 21

Бренд: Echo Страницы: 84

Бренд: Sparky Group Страницы: 94

Бренд: Sparky Group Страницы: 94

Бренд: Echo Страницы: 72

Бренд: Zenoah Страницы: 148

Бренд: EarthWise Страницы: 42

Бренд: Makita Страницы: 21

Бренд: Makita Страницы: 116

Бренд: Makita Страницы: 108

Бренд: Gardenline Страницы: 8

Бренд: Gude Страницы: 65

Бренд: PowerBase Страницы: 44

Бренд: Maxx Страницы: 134

Бренд: Mitox Страницы: 52

Бренд: Mitox Страницы: 40

Бренд: Mitox Страницы: 44

Бренд: Mitox Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды