manualshive.com logo in svg
background image

24

t

RoubleshootinG

Poor performance of the engine and/or cutting mechanism can normally be prevented by carefully following these 

instructions.

Poor performance can easily be corrected even by a beginner.

When the engine does not function properly check the following three (3) points first.

•  Is the engine compression adequate?

•  Is fuel system in good condition and is enough fuel being supplied?

•  Is electrical system in good condition and is spark plug operating normally?

When there is serious trouble with the unit, do not try to repair it yourself but have your distributor or dealer do it for 

you. For detailed TROUBLESHOOTING refer to tables 1 and 2. Locate the problem on the following charts and repair 

as necessary.

reaching carburetor

Fuel is not reaching 

cylinder
No spark at high 

tension cord end.

Engine does not start (or

, is difficult to start)

Engine cranks

There is fuel in the tank

Fuel is reaching carburetor

Fuel is reaching cylinder

There is spark at high  tension cord end

There is spark at plug

Starting procedures  correct

No spark at plug
Fuel does not keep 

running

Acceleration and low 

speed function defective

Carburetor 

overflow

Engine does  

not crank
Fuel strainer 

clogged ..........

Clean.
Fuel pipe 

clogged ............

Clean.

Suction insuf-

ficient

 ................

Make sufficient.

Strainer clogged ..........................................Clean.

Carburetor out of order ................................Disassemble and check.
C.D.I. module defective ...............................Remove and replace.
Ignition coil defective ...................................Remove and replace.
Wire connection defective  ..........................Reconnect.

High-tension cord connection defective.......Repair as necessary.

Switch is grounded ......................................Switch on.
Insulator cracked .........................................Replace plug.
Spark gap incorrect .....................................Adjust.

Covered with carbon....................................Clean or replace.

Fouled with fuel ...........................................Clean or replace.
Starting procedures incorrect ......................Start correctly.
Low and high speed needle.........................Readjust.
setting too lean 

Metering lever spring too strong ..................Readjust.

Fuel pump diaphragm defective ..................Replace.
Fuel passage clogged with dust ..................Disassemble and clean.

Fuel leaking from fixing surfaces 

 ................Retighten all screws. 

of carburetor

Table 1 

Fuel is not 

Air valve, fuel tank cap does not 

work normally ..............................................Replace or Clean.
Fuel pump does not operate........................Check 

impulse drilling.
Fuel inlet needle valve clogged with dust ....Clean.

Metering lever spring not placed  

in dent of lever .............................................Correct.

Muffler sticky with fuel

 .................................Fuel mixture is too rich

 

Start the engine several 

times 

 

with choke rod fully open 

and

 

run at fast idle until engine  

 

does not smoke.

Bearing damaged ........................................Disassemble and 
replace.

Piston and/or cylinder seized.......................Disassemble and replace.
Crankshaft worn ..........................................Disassemble and replace.
Crankshaft contacting crankcase ................Disassemble and replace.

T

R

A

H

C

G

N

I

T

O

O

H

S

E

L

B

U

O

R

T

M

E

L

B

O

R

P

E

N

I

G

N

E

m

e

l

b

o

r

P

k

c

e

h

C

s

u

t

a

t

S

e

s

u

a

C

y

d

e

m

e

R

e

n

i

g

n

E

-

s

k

n

a

r

c

/

d

r

a

h

s

tr

a

t

s

t'

n

s

e

o

d

tr

a

t

s

r

o

t

e

r

u

b

r

a

c

t

a

l

e

u

F

r

o

t

e

r

u

b

r

a

c

t

a

l

e

u

f

o

N

d

e

g

g

o

lc

r

e

n

i

a

rt

s

l

e

u

F

d

e

g

g

o

lc

e

n

il

l

e

u

F

r

o

t

e

r

u

b

r

a

C

e

c

a

l

p

e

r

r

o

n

a

e

l

C

e

c

a

l

p

e

r

r

o

n

a

e

l

C

r

e

l

a

e

d

o

h

c

E

r

u

o

y

e

e

S

r

e

d

n

il

y

c

t

a

l

e

u

F

r

e

d

n

il

y

c

t

a

l

e

u

f

o

N

r

o

t

e

r

u

b

r

a

C

r

e

l

a

e

d

o

h

c

E

r

u

o

y

e

e

S

l

e

u

f

h

ti

w

t

e

w

r

e

lff

u

M

h

c

ir

o

o

t

e

r

u

tx

i

M

l

e

u

F

e

k

o

h

c

n

e

p

O

r

e

tli

f

ri

a

e

c

a

l

p

e

r/

n

a

e

l

C

r

o

t

e

r

u

b

r

a

c

t

s

u

j

d

A

r

e

l

a

e

d

o

h

c

E

r

u

o

y

e

e

S

d

n

e

t

a

k

r

a

p

S

e

ri

w

g

u

l

p

f

o

k

r

a

p

s

o

N

ff

o

h

c

ti

w

s

p

o

t

S

m

e

l

b

o

r

p

l

a

c

ir

t

c

e

l

E

h

c

ti

w

s

k

c

o

lr

e

t

n

I

N

O

o

t

h

c

ti

w

s

n

r

u

T

r

e

l

a

e

d

o

h

c

E

r

u

o

y

e

e

S

r

e

l

a

e

d

o

h

c

E

r

u

o

y

e

e

S

g

u

l

p

t

a

k

r

a

p

S

k

r

a

p

s

o

N

t

c

e

rr

o

c

n

i

p

a

g

k

r

a

p

S

n

o

b

r

a

c

h

ti

w

d

e

r

e

v

o

C

l

e

u

f

h

ti

w

d

e

lu

o

F

e

v

it

c

e

f

e

d

g

u

l

P

).

n

i

6

2

0

.

0

(

m

m

5

6

.

o

t

t

s

u

j

d

A

e

c

a

l

p

e

r

r

o

n

a

e

l

C

e

c

a

l

p

e

r

r

o

n

a

e

l

C

g

u

l

p

e

c

a

l

p

e

R

,

s

n

u

r

e

n

i

g

n

E

r

o

s

e

i

d

t

u

b

t

o

n

s

e

o

d

e

t

a

r

e

l

e

c

c

a

yl

r

e

p

o

r

p

r

e

tli

f

ri

A

y

tr

i

d

r

e

tli

f

ri

A

r

a

e

w

l

a

m

r

o

N

e

c

a

l

p

e

r

r

o

n

a

e

l

C

r

e

tli

f

l

e

u

F

y

tr

i

d

r

e

tli

f

l

e

u

F

s

e

u

d

is

e

r/

s

t

n

a

n

i

m

a

t

n

o

C

n

i

l

e

u

f

e

c

a

l

p

e

R

t

n

e

v

l

e

u

F

d

e

g

g

u

l

p

t

n

e

v

l

e

u

F

n

i

s

e

u

d

is

e

r/

s

t

n

a

n

i

m

a

t

n

o

C

l

e

u

f

e

c

a

l

p

e

r

r

o

n

a

e

l

C

g

u

l

P

k

r

a

p

S

n

r

o

w

/y

tr

i

d

g

u

l

P

r

a

e

w

l

a

m

r

o

N

e

c

a

l

p

e

r

r

o

t

s

u

j

d

a

d

n

a

n

a

e

l

C

r

o

t

e

r

u

b

r

a

C

t

n

e

m

t

s

u

j

d

a

r

e

p

o

r

p

m

I

n

o

it

a

r

b

i

V

t

s

u

j

d

A

m

e

t

s

y

S

g

n

il

o

o

C

m

e

t

s

y

s

g

n

il

o

o

C

d

e

g

g

u

l

p

/y

tr

i

d

n

i

n

o

it

a

r

e

p

o

d

e

d

n

e

tx

E

s

n

o

it

a

c

o

l

y

t

s

u

d

/y

tr

i

d

n

a

e

l

C

r

o

t

s

e

rr

A

k

r

a

p

S

n

e

e

r

c

S

r

o

t

s

e

rr

a

k

r

a

p

S

d

e

g

g

u

l

p

n

e

e

r

c

s

r

a

e

w

l

a

m

r

o

N

e

c

a

l

p

e

R

s

e

o

d

e

n

i

g

n

E

k

n

a

r

c

t

o

n

A

/

N

A

/

N

m

e

l

b

o

r

p

e

n

i

g

n

e

l

a

n

r

e

t

n

I

r

e

l

a

e

d

o

h

c

E

r

u

o

y

e

e

S

Содержание CS-301





























Отзывы: