manualshive.com logo in svg

Echo CS-301, Инструкция по эксплуатации, Страница: 17 / 28

Поделиться
Скачать
Echo CS-301 Скачать руководство пользователя страница 17

17

COMPONENT/

SYSTEM

MAINTENANCE

PROCEDURE

REQ'D

SKILL

LEVEL

DAILY OR

BEFORE

USE

EVERY

REFUEL

3

MONTHS

OR 90

HOURS

6

MONTHS

OR 270

HOURS

YEARLY

600

HOURS

Recommended Echo Dealer Maintenance Procedures

Cylinder Exhaust Port

Inspect/Clean/Decarbon

3

I / C

Do-It-Yourself Maintenance Procedures

Air Filter

Inspect/Clean/Replace

1

I / C

R *

Automatic Oiler

Inspect/Adjust

1

I

Oil Strainer

Inspect/Replace

1

I / R *

Fuel Strainer

Inspect/Replace

1

I

R *

Guide Bar & Oil Holes

Inspect/Clean

1

I / C

Sprocket

Inspect/Replace

2

I / R *

Spark Plug

Inspect/Clean/Replace

2

I / C

R *

Cooling System

Inspect/Clean

2

I / C

Muffler Spark Arrestor

Inspect/Clean/Replace

2

I / R *

Recoil Starter Rope

Inspect/Replace

1

I / R *

Screws/Nuts/Bolts

Inspect/Tighten/Replace

1

I / R *

MAINTENANCE PROCEDURE LETTER CODES:  I = INSPECT,  R = REPLACE,  C = CLEAN
IMPORTANT NOTE - 

Time intervals shown are maximum. Actual use and your experience will determine the frequency of required

maintenance.

MAINTENANCE PROCEDURE NOTES:

*

 All recommendations to replace are based on the finding of damage or wear during inspection..

m

aintenanCe

 

anD

 C

aRe

Your ECHO unit is designed to provide many hours of trouble free service. Regular scheduled maintenance will help 

your unitr achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take 

your unit to an ECHO Service Dealer for maintenance.  To help you decide whether you want to DO-IT-YOURSELF or 

have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed see your Echo dealer 

for repairs.

skill

 

levels

 

Level

 

1

 =  Easy to do. Most required tools come with unit.

 

Level

 

2

 =  Moderate difficulty. Some specialized tools may be required.

 

Level

 

3

 =  Experience required. Specialized tools are required. ECHO recommends 

 

 

 

that the unit be returned to your ECHO dealer for servicing.

ECHO offers 

REPOWER

TM

 Maintenance Kits and Parts to make your maintenance job easier. Just below each task 

heading are listed the various part numbers required for 

that task. See your ECHO dealer for these parts.

maintenanCe

 

inteRvals

Содержание CS-301





























Отзывы:

Нет отзывов