background image

13

INFORMATION

Kickback Safety Features

The following features are recommended for this model as Kickback Safety Features.

Double Guard Low Kick Type Guide Bar or Asymmetrical Low Kick Type Guide Bar

Note: Your saw chain can be equipped with either of these bars.

Reduced nose

radius

NOTE
Use Oregon

®

 Intenz

TM

 replacement guide bars.

The following guide bars may be considered to have equivalent kickback energy.

• Sprocket nose guide bars of the same length and nose radius, same pitch and having the same number of teeth.

• A hard nose guide bar having the same length and nose radius as a sprocket nose bar.

• Low Kick Guard Link Type Saw Chain

The low kick guard link chain must be maintained correctly. Follow instruction “SETTING THE CHAIN” in Instruction
Manual.

• Front Handle Guard

The front handle guard must be installed correctly and kept in good condition.

• Chain Brake

Chain brake must be maintained correctly. Follow instruction “CORRECT USE OF CHAIN BRAKE” in Instruction
Manual.

CAUTION !!

The consequences of using improper replacement components and of removing safety devices may result in serious
or fatal injury

Double Guard Bar

Содержание CS-3000 TYPE 1E

























Отзывы: