Echo CS-271T Скачать руководство пользователя

Страница: 32 / 36

CS-271T

STORAGE AFTER USE

* Technical data subject to change without notice.

TECHNICAL DATA

• Inspect and adjust every part of the chain saw.

- Completely clean every part and repair if

necessary.

- Apply thin coating of oil on metal parts to

prevent rust.

• Remove chain and guide bar.
• Drain fuel tank, pull starter slowly a few times to

drain fuel from carburetor.

• Pour a small amount of clean motor oil into spark

plug hole, pull starter and crank the engine until
piston reaches: TOP DEAD CENTER.

• Store in a dry area, free from dust.

WARNING

Do not store in an enclosure where fuel
fumes may accumlate or reach an open flame
or spark.

CAUTION

Do not lend or rent your chain saw without
the Instruction manual and Safety manual.

NOTE

• For future reference, you should keep this

Instruction manual and the Safety manual.

• If this Instruction manual or the Safety manual

has become illegible or is lost, please purchase
a new one from your ECHO dealer.

MODEL

CS-271T

Dimension

L × W × H

257 × 228 × 210 (10.1 in. × 8.98 in. × 8.27 in.)

Mass

Power head, dry

3.0 (6.61 lb.) Without chain and guide bar

Engine

Type

Air-cooled two-stroke single cylinder

Displacement

mL (cm³)

26.9 (1.64 cu. in.)

Carburetor

Diaphragm type

Magneto

Flywheel magneto: CDI system

Spark plug

NGK BPM8Y

Starter

Recoil starter

Power transmission

Automatic centrifugal clutch

Fuel

Mixture ratio

50 : 1 ratio with ECHO Power Blend X™, ISO-L- EGD
(ISO/CD 13738) and JASO M345-FC/FD two-stroke,
air-cooled engine oil.

Gasoline

Use 89 octane unleaded.
Do not use fuel containing methyl alcohol, more than
10 % ethyl alcohol or 15 % MTBE.
Do not use alternative fuels such as E-20 or E-85.

Tank capacity

0.24 (8.12 US. fl. oz.)

Oil

Bar and chain

ECHO bar and chain oil (or motor oil)

Tank capacity

0.16 (5.41 US. fl. oz.)

Guide bar and

See page 22 for Chain and Guide Bar Combination

saw chain

Lubrication

Adjustable automatic oil pump

Engine speed

Idle

r/min

2800 - 3600

Clutch engagement

r/min

4250 - 4750

Wide open throttle

r/min

11300 - 12500

Standard

Front hand guard, Anti-vibration device,
Throttle control lockout, Chain brake, Chain catcher,
Spark arrestor muffler, Kick guard,
(Spiked bumper;

option

)

Содержание CS-271T





































Результаты поиска

Содержание CS-271T

Отзывы:

Похожие инструкции для CS-271T

Бренды по названию

Популярные бренды

Echo CS-271T, Инструкция по эксплуатации

Результаты поиска

Содержание CS-271T

Отзывы:

Похожие инструкции для CS-271T

Бренды по названию

Популярные бренды