Echo CS-271T Скачать руководство пользователя

Страница: 27 / 36

CS-271T

Oil filter

Fuel filter

Oil tank cap

Fuel tank cap

0.65 mm (0.026 in.)

Cleaner cover knob

Air filter

Air cleaner cover

AIR FILTER

• Check before every use.
• Close choke (

• Turn cleaner cover knob counterclockwise by

hand and remove air cleaner cover and air filter.

• Brush off dust lightly, or clean with compressed

air, or replace the air filter.

• Reinstall air filter and cover.

CHECK FUEL SYSTM

• Check before every use.
• After refueling, make sure fuel does not leak

from around fuel pipe, fuel grommet or fuel tank
cap.

• In case of fuel leakage there is a danger of fire.

Stop using the machine immediately and request
your dealer to inspect or replace.

SPARK PLUG

• Check periodically.
• The standard spark gap is 0.65 mm

(0.026 in.).

• Correct the spark gap if it is wider or

narrower than the standard gap.

• Fastening torque: 15 to 17 N

(130 to 145 in. lb.).

FUEL FILTER

• Check periodically.
• Do not allow dust to enter fuel tank.
• A clogged filter will cause difficulty in starting

engine or abnormalities in engine performance.

• Pull the fuel filter out through fuel inlet port with a

piece of steel wire or the like.

• When the filter is dirty, replace it.
• When the inside of the fuel tank is dirty, rinsing

the tank out with gasoline can clean it.

OIL FILTER

• Check periodically.
• Do not allow dust to enter into oil tank.
• A clogged oil filter will affect the normal

lubricating system.

• Pull it out through oil filling hole with a piece of

steel wire or the like.

• If the filter is dirty, wash it in gasoline or replace

it.

• When the inside of the tank gets dirty, rinsing the

tank out with gasoline can clean it.

Содержание CS-271T





































Результаты поиска

Содержание CS-271T

Отзывы:

Похожие инструкции для CS-271T

Бренды по названию

Популярные бренды

Echo CS-271T, Инструкция по эксплуатации

Результаты поиска

Содержание CS-271T

Отзывы:

Похожие инструкции для CS-271T

Бренды по названию

Популярные бренды