background image

5 INCH PTO CHIPPER

4

SAFETY

1.7  saFeTY DeCals

See Section 1.6 for decal locations.  Familiarize yourself with all of the safety and operating decals on the machine 

and the associated hazards.  See the engine owner’s manual or contact the engine manufacturer for engine safety 

instructions and decals.  Make certain that all safety and operational decals on this machine are kept clean and in good 

condition. Decals that need replacement must be applied to their original locations. 

pn 12169

3

KEEP HANDS AND FEET OuT OF INlET AND 

 

DISCHARgE  OPENINgS  WHIlE  MACHINE 

IS  OPERATINg  TO  AVOID  SERIOuS  PER

-

SONAl INJuRy. AllOW MACHINE TO COME 

TO A COMPlETE STOP BEFORE ClEARINg 

OBSTRuCTIONS.

pn 12172

4

READ AND uNDERSTAND THIS OWN

-

ER/OPERATORS  MANuAl.    BE  COM

-

PlETEly  FAMIlIAR  WITH  THE  CON

-

TROlS  AND  THE  PROPER  uSE  OF 

THIS EQuIPMENT. OBTAIN AND WEAR 

SAFETy glASSES AND uSE HEARINg 

PROTECTION AT All TIMES WHEN OP

-

ERATINg THIS MACHINE. BEFORE IN

-

SPECTINg  OR  SERVICINg ANy  PART 

OF THIS MACHINE, SHuT OFF POWER 

SOuRCE, DISCONNECT SPARK Plug 

WIRE FROM SPARK Plug AND MAKE 

SuRE All MOVINg PARTS HAVE COME 

TO A COMPlETE STOP.

pn 12173

5

DO  NOT  OPERATE  THIS 

EQuIPMENT  IN  THE  VICIN

-

ITy  OF  BySTANDERS.  DO 

NOT  AllOW  CHIlDREN  TO 

OPERATE  THIS  EQuIPMENT.  

AlWAyS  STAND  ClEAR  OF 

DISCHARgE  AREA  WHEN 

OPERATINg THIS MACHINE.  KEEP FACE AND BODy AWAy 

FROM DISCHARgE AREAS.

pn 12174

6

DO NOT OPERATE MACHINE WITH

-

OuT  SHIElDS  IN  PlACE.  FAIluRE 

TO DO SO MAy CAuSE SERIOuS IN

-

JuRy OR DEATH.

PN 12174

pn 12175

7

KEEP HANDS AND FEET OuT OF 

INlET  AND  DISCHARgE  OPEN

-

INgS WHIlE MACHINE IS OPER

-

ATINg TO AVOID SERIOuS PER

-

SONAl INJuRy. AllOW MACHINE 

TO COME TO A COMPlETE STOP 

BEFORE ClEARINg OBSTRuCTIONS.

pn 12168

2

KEEP    HANDS,  FEET AND  BODy 

AWAy  FROM  DRIVElINE  WHIlE 

MACHINE  IS  OPERATINg  TO  

AVOID  ENTANglEMENT.  OPER

-

ATE MACHINE AT 540 RPM.

1

pn 12250

8

9

CHECK  BlADE  BOlTS  FOR 

PROPER  TORQuE  AFTER  EV

-

ERy  8  HOuRS  OF  OPERATION.  

CHECK  BlADES  AND  ROTATE 

OR  RESHARPEN  DAIly  OR  AS 

REQuIRED  TO  KEEP  BlADES 

SHARP.    REFER  TO  OWNERS 

MANuAl FOR INSTRuCTIONS.  FAIluRE TO DO SO MAy CAuSE 

POOR PERFORMANCE, DAMAgE OR PERSONAl INJuRy AND 

WIll VOID THE MACHINE WARRANTy.

pn 14942-00

pn 32109-00

READ AND uNDERSTAND yOu OWNERS MANuAl BEFORE 
OPERATINg.  IF OWNERS MANuAl WAS NOT INCluDED OR 
yOu  HAVE  ANy  QuESTIONS,  PlEASE  CAll  800.247.7335 
OR 701.282.5520 (u.S.A.)

DO  NOT  OPERATE  THIS 

EQuIPMENT 

IN 

THE 

VICINITy OF BySTANDERS.  

DO NOT AllOW CHIlDREN 

TO 

OPERATE 

THIS 

EQuIPMENT.    AlWAyS 

STAND 

ClEAR 

OF 

DISCHARgE 

AREA 

WHEN  OPERATINg  THIS 

MACHINE.  KEEP  FACE 

AND  BODy  AWAy  FROM 

DISCHARgE  AREAS.  ROTATE  THE  DISCHARgE  TuBE 

OVER THE HITCH BEFORE TOWINg AND lOCK SECuREly 

IN PlACE.

PN 12174

Содержание CH5540
























Отзывы: