background image

 

 

Operating Controls 

 

WARNING: Read, understand, and follow all 
instructions and warnings on the machine and 
in this manual before operating. 
 

SHIFT LEVER 

The shift lever is located between the lower handles. 
Place  the  shift  lever  into  any  of  five  positions  to 
control the direction of travel and ground speed. 

 

Forward 

There are four forward (F) speeds. Position one (1) is 
the slowest and position four (4) is the fastest. 

Reverse 

There is one reverse (R) speed. 

Primer 

Depressing  the  primer  forces  fuel  directly  into  the 
engine’s carburetor to help with starting the machine 
in cold weather. 

 

CHOKE CONTROL 

 

The choke control is found on the rear of the engine 
and  is  activated  by  rotating  the  knob  clockwise. 
Activating the choke control closes the choke plate 
on the carburetor and helps start the engine. 

 

THROTTLE CONTROL 

The  throttle  control  is  located  on  the 
engine.  It  regulates  the  speed  of  the 
engine and will shut off the engine when 
pushed down completely. 

 

AUGER CONTROL 

 

The  auger  control  is  located  on  the  left  handle. 
Squeeze  the  control  grip  against  the  handle  to 
engage the augers and start throwing snow. Release 
the control grip to stop. 

 

DRIVE CONTROL 

 

The  drive  control  is  located  on  the  right  handle. 
Squeeze the control grip against the handle to engage 
the wheel drive. Release the grip to disengage it. 

 

 

 

Содержание SNOW24
















Отзывы: