background image

22

7- INSTALLATION

7.1 Selection of Location of Boiler 

The boiler must be installed in accordance with gas safety regulations and relevant standards. Additionally, 
the clearance around the boiler should be as shown in fig 10. In order to make service, maintenance and 
usage easier.  

Figure 10: It shows the minimum distances required from the top and sides of the boiler (Dimensions given 
in mm). 

The installation must comply with the following minimum distances so that servicing and maintenance of 
the  boiler  can  be  performed  correctly.  The  position  of  the  boiler  must  be  checked  against  technical 
requirements. 

Figure 10.Combi Mounting Clearances  Figure 11.Isolation Valve Cover Mounting

 

 CAUTIONS : 

Do not install your boilers in locations that will be exposed to direct sunlight. Sunlight can

cause color change on the exterior of your boiler over time.

Ambient temperature of boiler's installation location should be between 5 -35

0

C.

The boiler can be used at altitudes up to 2000 m above sea level.

There is no need to remove side panels in the combi boiler service operations.

 

Minimum

50 mm clearances are  given taking into consideration    the share of possible side panel

sheet changes. 

Since the outside temperature of the boiler 

does not rise above 85 ° C at the maximum heating power, no

special protective measures are required against the combustible construction materials and components.

It  is  not  recommended  to  install 

“Isolating  Valve  Cover”  (figure  11)  to  the

boiler if kitchen cupboard is used for installation place. It can be used at open
space areas to hide valve set and filling loop.

Содержание 8116450110
















































Отзывы: