Ebyte E831-RTU(8080T-485) Скачать руководство пользователя | Manualshive

Страница: 6 / 22

background image

1.2. Simple use

Wiring: The computer is connected to E831-RTU (8080T-485) via USB to RS485.
Power supply: E831-RTU (8080T-485) working voltage is DC 8 ~ 28V, 12V or 24V is

recommended.

1.2.1. RS485 bus control

Select the corresponding model and port, and click Search to search for the device.

When the device is searched, click "Stop"

«
...
4
5
6
7
8
...
»

Содержание E831-RTU(8080T-485)























Отзывы:

Нет отзывов

Похожие инструкции для E831-RTU(8080T-485)

Бренд: ABB Страницы: 139

Бренд: ABB Страницы: 28

Бренд: ABB Страницы: 59

Бренд: vacuubrand Страницы: 12

Бренд: Vacon Страницы: 47

Бренд: Vacon Страницы: 40

Бренд: CAME Страницы: 2

traxon e:cue LCE-mx

Бренд: Osram Страницы: 35

Optidrive Elevator

Бренд: Invertek Страницы: 5

Бренд: Techtrol Страницы: 4

Бренд: Midland Страницы: 37

Бренд: Variotech Страницы: 24

SmartConnect SCM-NM

Бренд: Zeta Alarm Limited Страницы: 7

Бренд: Castell Страницы: 7

Бренд: Vector Страницы: 22

Бренд: CAME Страницы: 2

Бренд: LOVATO ELECTRIC Страницы: 8

Бренд: Qorvo Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды