Ebyte E01-2G4M27SX Скачать руководство пользователя страница 10

Страница: 10 / 12

hengdu Ebyte Electronic Technology Co.,Ltd.

E01-2G4M27SX

User Manual

，

Chengdu Ebyte Electronic Technology Co.,Ltd.

7. Welding operation guidance

7.1 Reflow soldering temperature

Profile Feature

Curve characteristics

Sn-Pb Assembly

Pb-Free Assembly

Solder Paste

Solder paste

Sn63/Pb37

Sn96.5/Ag3/Cu0.5

Preheat Temperature min

（

Tsmin

）

Min preheating temp.

100℃

150℃

Preheat temperature max (Tsmax)

Mx preheating temp.

150℃

200℃

Preheat Time (Tsmin to Tsmax)(ts)

Preheating time

60-120 sec

Average ramp-up rate(Tsmax to Tp)

Average ramp-up rate

3℃/second max

Liquidous Temperature (TL)

Liquid phase temp.

183℃

217℃

Time

（

）

Maintained Above

（

）

Time below liquid

phase line

60-90 sec

30-90 sec

Peak temperature

（

）

Peak temp.

220-235℃

230-250℃

Aveage ramp-down rate

（

Tp to Tsmax

）

Aveage ramp-down

rate

6℃/second max

Time 25℃ to peak temperature

Time to peak

temperature for 25℃

6 minutes max

8 minutes max

7.2 Reflow soldering curve

图

7-1

回流焊曲线图

Содержание E01-2G4M27SX












Результаты поиска

Содержание E01-2G4M27SX

Отзывы:

Ebyte E01-2G4M27SX, Руководство пользователя, Страница: 10 / 12

Результаты поиска

Содержание E01-2G4M27SX

Отзывы: