ebm-papst R3G710-AP02-01 Скачать руководство пользователя

Страница: 9 / 15

Operating instructions

R3G710-AP02-01

Translation of the original operating instructions

Fig. 3: Cable routing for fans installed upright.

4.4 Factory settings

Factory settings with which the device is pre-set by ebm-papst.

Control mode
parameter set 1

PWM controlling

Control mode
parameter set 2

PWM controlling

Fan / device adress

Max. PWM / %

100

Min. PWM / %

5,1

Save set value to
EEPROM

Yes

Set value control

Analogue (linear)

Control function
parameter set 1

Positive (heating)

Control function
parameter set 2

Positive (heating)

Item no. 52489-5-9970 · ENG · Revision 209539 · Release 2021-02-01 · Page 9 / 15

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com

Содержание R3G710-AP02-01
















Результаты поиска

Содержание R3G710-AP02-01

Отзывы:

Похожие инструкции для R3G710-AP02-01

Бренды по названию

Популярные бренды

ebm-papst R3G710-AP02-01, Руководство по эксплуатации

Результаты поиска

Содержание R3G710-AP02-01

Отзывы:

Похожие инструкции для R3G710-AP02-01

Бренды по названию

Популярные бренды