Operating instructions
A6E710-AR03-01
Translation of the original operating instructions
3.2 Nominal data
Motor
M6E110-IA
Phase
1~
Nominal voltage / VAC
230
Frequency / Hz
50
Method of obtaining
data
ml
Valid for approval/
standard
CE
Speed (rpm) / min
-1
900
Power consumption / W
630
Current draw / A
2.79
Capacitor / µF
14
Capacitor voltage / VDB
450
Max. back pressure / Pa
105
Min. ambient
temperature / °C
-40
Max. ambient
temperature / °C
65
Starting current / A
6.9
Max. safe operating
speed (rpm) /
min
-1
1140
@ 70 °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Data according to Commission Regulation (EU) 327/
2011
Actual
Req. 2015
01 Overall efficiency η
es
/ %
33.4
32.3
02 Measurement category
A
03 Efficiency category
Static
04 Efficiency grade N
41.1
40
05 Variable speed drive
No
06 Year of manufacture
The year of manufacture is specified on the
product's rating label.
07 Manufacturer
ebm-papst Mulfingen GmbH & Co. KG
Amtsgericht (court of registration) Stuttgart
· HRA 590344
D-74673 Mulfingen
08 Type
A6E710-AR03-01
09 Power consumption P
e
/ kW
0.61
09 Air flow q
v
/ m³/h
7510
09 Pressure increase total p
sf
/
Pa
99
10 Speed (rpm) n / min
-1
900
11 Specific ratio
*
1.00
12 Recycling/disposal
Information on recycling and disposal is
provided in the operating instructions.
13 Maintenance
Information on installation, operation and
maintenance is provided in the operating
instructions.
14 Additional components
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.
*
Specific ratio = 1 + p
fs
/ 100 000 Pa
Data obtained at optimum efficiency level. The ErP data is determined using a motor-impeller
combination in a standardized measurement setup.
3.4 Technical description
Weight
12.7 kg
Fan size
710 mm
Rotor surface
Cast in aluminum
Terminal box material
PP plastic
Blade material
Sheet aluminum insert, sprayed with PP
plastic
Number of blades
5
Blade pitch
-10°
Airflow direction
"V"
Direction of rotation
Counterclockwise, viewed toward rotor
Degree of protection
IP54
Insulation class
"F"
Moisture (F) /
Environmental (H)
protection class
F3-1
Installation position
Shaft horizontal or rotor on bottom; rotor
on top on request
Condensation
drainage holes
On rotor side
Mode
S1
Motor bearing
Ball bearing
Touch current
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
<= 3.5 mA
Electrical hookup
Via terminal box, capacitor integrated and
connected
Motor protection
Thermal overload protector (TOP) with
basic insulation
with cable
Axial
Protection class
I (with customer connection of protective
earth)
Motor capacitor
according to EN 60252-
1 in safety protection
class
S0
Conformity with
standards
EN 61800-5-1; CE
Approval
CCC; VDE; EAC
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. This does not however in any way affect the
technical properties of the products. The product is to be protected against
UV radiation to prevent the formation of patches and fading. Changes in
color are not a reason for complaint and are not covered by the warranty.
Item no. 10158-5-9970 · ENU · Change 89349 · Approved 2016-10-06 · Page 5 / 12
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com
