1 B a s i c Ta s k s
· Connect audio signal cables, power cable, and, if needed, computer cable.
· Select the operating mode, input signal type(s), and temperature/humidity conditions.
· Select the signal source(s) for each input channel.
· Select the loudspeaker type for each input channel and assign the output channel(s).
· Adjust the amplifier and listening distance parameters for the output channel(s).
· Adjust input channel EQ, gain, polarity, and delay.
· For Generic Processing, use EAWPilot to adjust output channel EQ, gain, polarity, limiting, and delay.
2 H a r d w a r e I n s t a l l a t i o n
2.1 AC MAINS
Universal power supply maximum operating range is 100 V to 240 V, 50 Hz to 60 Hz
Use supplied IEC-type ac mains cable with Nema connector for nominal 115 V or with Schuko connector for nominal 230 V.
2.2 INPUTS A TO D
Cable:
2 conductor plus shield
Mating Connector:
XLR-3 male
Analog:
Pin 1
Shield
Pin 2
or high
Pin 3
Signal - or low
Digital (AES/EBU):
Pin 1
Signal ground (shield)
Pin 2
Signal
Pin 3
Signal
2.3 OUTPUTS 1 TO 8
Cable:
2 conductor plus shield
Mating Connector:
XLR-3 female
Analog:
Pin 1
Shield
Pin 2
or high
Pin 3
Signal - or low
2.4 ETHERNET
For control of the processor using EAWPilot.
Cable:
Ethernet CAT-5 cable or better
Mating Connector:
RJ-45
Wiring Configuration:
Crossover (supplied ) for direct to computer connection
Standard for connection to a hub or switch
2.5 U-NET
For networking audio and computer control between multiple U-Net enabled products.
Cable:
Ethernet CAT-5 cable or better
Mating Connector:
RJ-45
Wiring Configuration:
Standard or crossover (supplied): the ports auto-sense the wiring
3 E AW P i l o t S o f t w a r e I n s t a l l a t i o n
Install the EAWpilot™ program on a computer with the Microsoft® Windows operating system: XP, 2000, NT, ME, or Windows 98.
See EAWPilot’s Help file for EAWPilot’s operating instructions.
UX 8800
Speaker / System Processor
INPUT CHANNELS
OUTPUT CHANNELS
ETHERNET
Clip
Lim
-12
Sig
Clip
Lim
-12
Sig
Clip
Lim
-12
Sig
Clip
Lim
-12
Sig
Clip
Lim
-12
Sig
Clip
Lim
-12
Sig
Clip
Lim
-12
Sig
Clip
Lim
-12
Sig
Clip
-6
-12
Sig
Clip
-6
-12
Sig
Clip
-6
-12
Sig
Clip
-6
-12
Sig
U-NET
1
2
LEVEL
CH
X-OVER
LIM
EQ
PROG
DELAY
UTIL
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
A
B
C
D
1
2
3
4
5
6
7
8
Crossover
Limiter
EQ
SELECT
UX8800 Front Panel
UX8800 Rear Panel
2
1
ANALOG
PUSH
ANALOG/AES
ANALOG/AES
PUSH
PUSH
D
C
A
ANALOG
PUSH
B
1 Shield
2+
3-
2+
3-
1 Shield
2 Signal
1 Signal Earth
(cable shield)
3 Signal
ANALOG
Output Input
DIGITAL
Input
FRONT PANEL
Ethernet Port / U-Net Indicators
REAR PANEL
U-Net Ports
2
1
U-NET
U-NET
ETHERNET
ETHERNET
U-NET
U-NET
1
2
UX8800 DIGITAL SIGNAL PROCESSOR
QUICK START - Loudspeaker Processor Mode
All manuals and user guides at all-guides.com
all-guides.com
