manualshive.com logo in svg

EAW KF740, Руководство пользователя

Поделиться
Скачать
EAW KF740 Скачать руководство пользователя страница 19

 

6.7.2 

Stacking the First Enclosure (Fly-Bar as the base) 

CAUTION: When attaching Hinges to Hinge Tubes in step 4, use the correct holes as determined 
by the Resolution or by the user-desired angles to achieve the desired aiming angle. Failure to 
follow this instruction can result in poor acoustical performance. 
 

1.  Lift a KF740 from its pallet and turn it upside down, so the Hinges on the enclosure are 

on the bottom. Position it onto the Fly-Bar so its Hinges line up the Fly-Bar Hinge Tubes.  

2.  Remove the four or six Quick Release Pins from the Hinges. 
3.  If they do not drop from gravity, slide the four Hinges of the enclosure down into the 

Hinge Tubes on the Fly-Bar. 

4.  Attach each Hinge to the Hinge Tube by inserting a Quick Release Pin (removed in Step 

2). Use holes 1-A in the front and 2-B in the rear.  

5.  Use the handles on the loudspeaker to lift the rear of the enclosure as far as possible and 

insert a Quick Release Pin (removed in step 2) into each of the enclosure’s rear Hinge 
Tubes as a locking pin.  

 

6.7.3 

Stacking Additional Enclosures (Fly-Bar as the base) 

CAUTION: When attaching Hinges to Hinge Tubes in step 5, use the correct holes as determined 
by Resolution or by the user-desired angles to achieve the desired splay angle. Failure to follow 
this instruction can result in poor acoustical performance. 

 

1.  Lift a KF740 from its pallet and turn it upside down, so the Hinges on the enclosure are 

on the bottom. 

2.  Lift the enclosure onto the stack mating the alignment pads and recesses between them.  
3.  Remove the four Quick Release Pins from the Hinges of the upper enclosure and the 

spare two pins in the lower enclosure. 

4.  If they do not drop from gravity, slide the four Hinges on the upper enclosure down into 

the Hinge Tubes on the enclosure below it. 

5.  Attach each Hinge to the Hinge Tube by inserting a Quick Release Pin (removed in Step 

9) through both.  

6.  Use the loudspeakers handles to lift the rear of the enclosure as far as possible and 

insert a Quick Release Pin (removed in step 2) into each of the enclosure’s rear Hinge 
Tubes as a locking pin.  

7.  Repeat steps 1 to 6 for additional enclosures.  

KF740 OWNER’S MANUAL   Page 19 of 22 

Содержание KF740























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды