Eaton Powerware 9125 Скачать руководство пользователя страница 8

Страница: 8 / 78

INTRODUCTION

EATON

Powerware

9125 Two-in-One UPS (2500/3000 VA) User’s Guide

164201374 Rev D

www.powerware.com

Start-on-battery capability for powering up the UPS even if utility
power is not available.

Hot-swappable batteries that simplify maintenance by allowing you to
replace batteries safely without powering down the critical load.

Emergency shutdown control through the remote emergency
power-off (REPO) port.

Optional X-Slot

cards with enhanced communication capabilities for

increased power protection and control.

Network transient protector that guards your network
communications equipment from surges. Low voltage models can
also protect modems, fax machines, or other telecommunications
equipment.

Advanced power management with the Software Suite CD for
graceful shutdowns and power monitoring.

Sequential shutdown and load management through separate
receptacle groups, called load segments.

Flash memory provides easy upgrades or reconfiguration capability
without requiring a service call.

Backed by worldwide agency approvals.

Содержание Powerware 9125















































































Результаты поиска

Содержание Powerware 9125

Отзывы:

Бренды по названию

Популярные бренды

Eaton Powerware 9125, Руководство пользователя

Результаты поиска

Содержание Powerware 9125

Отзывы:

Бренды по названию

Популярные бренды