Eaton Powerware 9125 Скачать руководство пользователя | Manualshive

Страница: 10 / 78

background image

SAFETY WARNINGS

EATON

Powerware

®

9125 Two-in-One UPS (2500/3000 VA) User’s Guide

S

164201374 Rev D

www.powerware.com

4

C A U T I O N

S

Batteries can present a risk of electrical shock or burn from high short-circuit current.
Observe proper precautions. Servicing should be performed by qualified service
personnel knowledgeable of batteries and required precautions. Keep unauthorized
personnel away from batteries.

S

Proper disposal of batteries is required. Refer to your local codes for disposal
requirements.

S

Never dispose of batteries in a fire. Batteries may explode when exposed to flame.

Sikkerhedsanvisninger

VIGTIGE SIKKERHEDSANVISNINGER
GEM DISSE ANVISNINGER
DENNE BRUGERVEJLEDNING INDEHOLDER VIGTIGE
SIKKERHEDSANVISNINGER

F A R E

Denne UPS indeholder LIVSFARLIG HØJSPÆNDING. Alle reparationer og vedligeholdelse bør
kun udføres af en AUTORISERET SERVICETEKNIKER. Ingen af UPS’ens indvendige dele kan
repareres af brugeren.

A D V A R S E L !

S

Denne UPS indeholder egen energiforsyning (batterier). Udgangsnetstikkene kan lede
strøm, selv når UPS’en ikke er tilsat en AC-energikilde.

S

Netledningen må ikke fjernes og stikket må ikke trækkes ud, mens UPS’en er tændt.
Dette fjerner sikkerhedsjorden fra UPS’en og fra det udstyr, der er sat til.

S

Installér denne UPS i et temperatur- og fugtighedskontrolleret indendørsmiljø, frit for
ledende forureningsstoffer for at formindske risikoen for brand og elektrisk stød.
Rumtemperaturen må ikke overstige 40

°

C. UPS’en bør ikke betjenes nær vand eller høj

fugtighed (maksimalt 95%).

S

I overensstemmelse med internationale normer og bestemmelser for el-installation må
det udstyr, der er forbundet til udgangen af denne UPS, tilsammen ikke overskride en
jordafdelingsspænding på mere end 1,5 milliampere.

S

For UPS systemer med hårdledningsudgange, skal overstrømsbeskyttelse for
vekslestrømmens udgangskredsløb forsynes af andre.

S

For UPS systemer med hårdledningsudgange, skal egnede, nominelle afbryderkontakter
for vekslestrømmens udgangskredsløb forsynes af andre.

«
...
8
9
10
11
12
...
»

Содержание Powerware 9125















































































Отзывы:

Нет отзывов

Похожие инструкции для Powerware 9125

Бренд: ABB Страницы: 2

imageRUNNER ADVANCE C9075S PRO

Бренд: Canon Страницы: 20

Бренд: Ebyte Страницы: 34

Бренд: YASKAWA Страницы: 61

Бренд: Yardney Страницы: 8

ACTIVE DRIVER M/M 1.1

Бренд: DAB Страницы: 10

Бренд: d&b audiotechnik Страницы: 3

ACTIVE DRIVER M/M 1.1

Бренд: DAB PUMPS Страницы: 38

Бренд: Jabra Страницы: 4

Бренд: Sanhua Страницы: 3

Бренд: QED Страницы: 26

Бренд: Samson Страницы: 8

Бренд: Samson Страницы: 60

Бренд: Samson Страницы: 40

Бренд: vacuubrand Страницы: 12

Бренд: Vacon Страницы: 47

Бренд: Vacon Страницы: 40

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды