2
ARTICLES REQUIS:
(à acheter séparément)
• Tournevis cruciforme
• Calfeutrage en silicone étanche pour l’extérieur
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
Des précautions de base doivent être suivies lors de l’utilisation de ce produit, incluant :
• Le respect de tous les avertissements incluant les avertissements ci-dessous ET ceux
indiqués sur le produit.
• Conservez ces instructions et ces avertissements.
• Exclusivement réservé à un usage extérieur.
• Homologation cULus pour l’utilisation dans des endroits humides.
• Le démontage de l’appareil annule la garantie.
• L’appareil est câblé et assemblé à l’avance pour faciliter son installation.
• Lisez et suivez ces instructions.
• Risque d’incendie ou de décharge électrique. Si vous n’êtes pas qualifié, consultez
un électricien.
• Coupez l’alimentation électrique depuis le fusible ou le disjoncteur avant l’installation
ou l’entretien.
MISE EN GARDE
• Raccordez le luminaire à une source d’alimentation de 120 V, 60 Hz. Tout autre
raccordement annule la garantie.
• L’appareil d’éclairage doit être installé par des personnes ayant l’expérience du
câblage domestique ou par un électricien qualifié. Le système électrique et la
méthode de raccordement électrique de l’appareil d’éclairage doivent être conformes
au Code national de l’électricité et aux codes locaux du bâtiment.
the holes in your junction box), attach the mounting
bracket (B) to your junction box (Fig. 4).
2.
Thread fixture wires through coverplate
gasket (C) (Fig. 7).
3.
Hang one end of the support hook onto the
mounting bracket and hang the light fixture on the
other end of the support hook (Fig. 5).
4.
Connect house ground wire and fixture ground wire.
Connect fixture black wire to house black wire
and fixture white wire to house white wire by
firmly pushing into quick connect wiring connectors
(Fig. 7)
5.
Remove support hook (H) and attach fixture (A) to
the mounting bracket (B) using (2) #8 x 1-1/4 in.
screws (F) pre-attached to the canopy. Be sure no
loose wires remain sticking out from underneath the
coverplate. Insert the decorative screw cover caps
(G) into the screw holes on the coverplate for a
finished appearance (Fig. 6).
6.
Adjust light fixture to desired postion
7.
Apply silicone caulk around the edges of the
coverplate to provide a watertight seal from
rain and moisture.
8.
Turn on power at main fuse / breaker box.
TROUBLESHOOTING
Problem
Cause / Solution
Light does not
come ON with
motion at night.
No power to the fixture.
• Check if circuit breaker tripped.
• Confirm wall switch is ON.
• Check app settings
Surrounding external ambient light is too bright. (If so, the unit may
think it is daytime.)
• Re-aim the head.
• Relocate or reposition the unit away from the light.
TURN OFF POWER BEFORE CONTINUING
Wiring to the unit is loose.
• Check wiring; reconnect if necessary.
Light
comes ON
for no apparent
reason at night.
There is motion in the detection zone.
• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.
TEST FOR YOURSELF.
• Cover the sensor lens with cardboard to prevent sensor
from detecting motion. If the light stays off, something in the
detection zone is triggering the sensor.
* If the light stays on with the sensor lens covered, contact
customer service.
• Reposition the sensor.
Light stays ON at
night and does
not turn OFF.
There is motion in the detection zone.
• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.
• Reposition the sensor.
If there is no motion in the detection zone, unit is in an override
mode. Check app settings.
Light
continuously
blinks ON and
OFF at night.
The light given from the unit’s own lamp is affecting the
motion sensor.
• Re-aim the lamp.
• Reposition motion sensor.
Light is ON
during the day.
The motion sensor is in “TEST” mode.
• Inactivate “TEST” mode in the app.
The motion detector is shadowed.
• Reposition motion sensor.
5-YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Eaton warrants to customers that, for a period of five years from the date of purchase, Eaton
products will be free from defects in materials and workmanship. The obligation of Eaton
under this warranty is expressly limited to the provision of replacement products. This
warranty is extended only to the original purchaser of the product. A purchaser’s receipt or
other proof of date of original purchase acceptable to Eaton. This is required before warranty
performance shall be rendered. This warranty does not apply to Eaton products that have
been altered or repaired that have been subjected to neglect, abuse, misuse or accident
(including shipping damages). This warranty does not apply to products not manufactured by
Eaton which have been supplied, installed, and/or used in conjunction with Eaton products.
Damage to the product caused by replacement bulbs or corrosion or discoloration of brass
components are not covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL EATON BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT,
STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL
THE LIABILITY OF EATON FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED
WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR
MODIFICATION OF EATON PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE,
EXCEED THE PURCHASE PRICE OF EATON PRODUCTS GIVING RISE TO A CLAIM. NO LABOR
CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.
To obtain warranty service, please contact Eaton at 1-800-334-6871, press option 2 for
Customer Service, or via e-mail [email protected] and include the following
information:
• Name, address and telephone number
• Date and place of purchase
• Catalog and quantity purchase
• Detailed description of problem
All returned products must be accompanied by a Return Goods Authorization Number issued
by the Company and must be returned freight prepaid. Any product received without a Return
Goods Authorization Number from the Company will be refused. Eaton is not responsible for
merchandise damaged in transit. Repaired or replaced products shall be subject to the terms
of this warranty and are inspected when packed. Evident or concealed damage that is made
in transit should be reported at once to the carrier making the delivery and a claim filed
with them.
Reproductions of this document without prior written approval of Eaton are strictly prohibited.
For assistance, call 1-800-334-6871 or e-mail us at [email protected]
Printed in China
A
6
F
F
G
G
FRANÇAIS
AVERTISSEMENT
4
D
D
Junction box
B
C
A
E
E
B
7
5
