background image

 
 

INSTALLATION SPECIFICATION 

 

Eaton Industries Pty Ltd 

 

August 2010 

10 Kent Road, Mascot, NSW 2020, Australia 

 

Page 

1

 of 

13

 

 

 

DOCUMENT# 510091 

E S F   S U R G E   P O W E R   F I L T E R  

I N S T A L L A T I O N   G U I D E  

Dear Installer, 

To ensure you get the maximum benefit from this product, we ask that you carefully 
follow this installation specification. This instruction forms part of your installation 
record. Please read it thoroughly prior to commencing work and ensure that it is 
retained afterward by the equipment owner.  

Prior to commencing installation, please read the ‘

Application Statement

’ and 

complete the supplied checklists. Not completing the checklists may result in 
unpredictable performance and/or equipment damage. Eaton shall not be responsible 
for any issue arising as a result of the installation not being carried out according to 
this document. 

If you are unsure about any aspect of installing this product, or require clarification of 
any issue, please contact your local Eaton distributor or office. 

 

 

PREPARATION FOR INSTALLATION 

Prior to installation, please read the following application statement then follow the checklist after to make 
sure you are ready to commence the job. 

 

Application Statement: 

“This Surge Protective Device (SPD) is designed to provide electrical protection to 
sites using a conventional, low voltage supply with a grounded neutral. For proper 
performance, it must be installed according to the supplied instructions, as well as any 
applicable local standards and laws. This unit is intended to reduce the risk of damage 
resulting from lightning strikes, power network transients and other associated 
phenomena. No product can completely eliminate risk and it is essential that 
connected loads also be compliant to the standards applicable to ensure proper 
coordination with this unit. Only suitably-qualified personnel shall install this unit.” 

 

Please contact your local Eaton distributor or office if you do not agree with the “Application Statement”, 
otherwise please proceed to the checklist over page. 

Содержание ESF Series














Отзывы: