3. Power controlled output: This feature maintains consistent
light output during the entire 90 minutes of emergency
operation ensuring there is no drop in lumen output as the
battery voltage drops.
Field Installation Classification (EBPLED7W, EBPLED14W)
1. Determine electrical compatability with fixture: Verify the
emergency driver wattage (7 watts or 14 watts depending
on model) does not exceed the drivers AC input. Also, verify
that the forward voltage of the LEDs are within the operating
parameters of the selected model (see table below).
Output Power (W) Min Vf (V) Max Vf (V)
EBPLED7W
7
8
55
EBPLED14W
14
16
55
2. Calculate Lumen output during emergency operation:
Go to the website www.designlights.org and identify the
light fixture by using the available search criteria. Determine
the fixture rated data – efficacy in lumens/watt. Multiply
the fixture efficacy by the output wattage of the selected
emergency battery pack to determine the lumen output of
the fixture during emergency operation.
Example: Fixture efficacy = 100 lumens/watt
EBPLED7W provides 7 watts of constant power
(Use 14W for EBPLED14W)
Fixture output = 100 lumens/watt X 7 watts = 700
lumens during emergency operation
3. Insure means of egress lighting levels: Follow industry
standard methods of lighting layout to determine placement
of emergency battery pack equipped fixtures. Verify the
selected EBP will provide sufficient lumen output to meet
path of egress illumination requirements.
INSTALLATION
1. Mounting The EBP can be mounted inside a fixture channel,
on the back of a fixture, or near the fixture. The flex conduit
should be connected to a junction enclosure which allows
access to the wiring connections for grounding.
(Note: EBP assemblies without conduit must be factory
installed in the wireway of the fixture).
2. Wiring Refer to the block diagram below for the wiring of the
LED load, AC driver, and AC power.
The unswitched AC power for the EBP and the power for the
AC driver should be from the same branch circuit to prevent
disconnecting 2 sources of power and the battery during
servicing.
3. Mounting the Test Button / Indicator Light / Laser Input
Mount the Test Button / Indicator Light / Laser Input so the
indicator light is visible once the fixture is installed. Proper
mounting is required for accessibility and functionality of the
laser input testing feature and EZ key battery disconnect.
OPERATION
Once AC power is permanently applied to the blue wire of the
fixture remove the EZ key and store it for later use. When AC
power is applied, the charging indicator light is illuminated,
indicating the battery is being charged. When the power fails,
the emergency ballast automatically switches to emergency
power, operating its LED load at the rated output for at least 90
minutes.
NOTE: The battery is not fully charged until 24 hours after the
AC power is applied.
MAINTENANCE
Although no routine maintenance is required to keep the
emergency LED driver functional, it should be checked
periodically to verify proper operation. Follow any applicable
local or national codes. The following schedule is the minimum
required to meet NFPA 101 standards:
1
. Visually inspect that the charging light is illuminated
monthly.
2. Test the emergency operation of the fixture monthly for a
minimum of 30 seconds. Perform the test by pressing the
test button / indicator light for 30 seconds or aiming a laser
pointer at the clear test button. The LED load should operate
at the rated output.
(Note: The laser test will not trigger if the ambient light is
too high. The light must be switched off in fixtures where the
test button is in close proximity to the light, or the test will
need to be triggered mechanically)
3. Conduct a 90 minute discharge test annually by
disconnecting the unswitched power. The LED load should
operate at the rated output for at least 90 minutes.
4. Keep written records of testing
Refer any service requirements indicated by these
checks to qualified personnel.
WARRANTIES AND LIMITATION OF LIABILITY
Please refer to www.eaton.com/LightingWarrantyTerms for our
terms and conditions.
Image of Test Button / Indicator Light / Laser Input
With Battery Disconnected (Left)
Without Battery Disconnected (Right)
Eaton
1121 Highway 74 South
Peachtree City, GA 30269
eaton.com/lighting
© 2015 Eaton
All Rights Reserved
Printed in USA
Publication No. IB505009EN
Eaton is a registered trademark.
All trademarks are property
of their respective owners.
Test Button /
Indicator Light /
Laser Input /
Battery Disconnect
Emergency Driver
EBPLED
LED Load
AC Driver
Outside of fixture color is WHT
120-277VAC Neutral WHT
Outside of fixture color is BLK
Power for AC Driver WHT/BLK
WHT/BLK
Plenum
Wire
RED/WHT
BLU/WHT
RED
Outside of fixture color is BLU
Unswitched 120-277VAC
50/60 Hz BLK/ORG
L
L
+
+
N
N
-
-
Block Diagram of
wiring for EBPLED
