Eaton Crouse-Hinds 8506A-CS-P1 Скачать руководство пользователя страница 7

 

DOCUMENT 2421 

REV. L 

 

Instruction Manual 

ICAO Approach Fixture 

 

 

 

 

  
 

6

 

General Description 

 

6.1

 

ICAO Approach Light 

 

The Crouse-

Hinds ICAO Approach Light is a Style II, (≤1/2 inch) fixture that meets the 

photometric requirements of ICAO Annex 14 fixtures 2.1, 2.2, 2.3, 2.4, and 2.8 with the 
appropriate lamp(s) and colored lens/lenses installed.  It is designed for installation at the 
runway threshold or any other location where visual guidance of moving aircraft is desirable.  
The fixture is designed to fit on a FAA L-868 (do not install on shallow base), steel, size B 
light base per FAA AC 150/5345-42 (latest version), and have a total height above 
grade/ground level of 

<

 .500 inch.  The fixture is uni-directional, projecting the beam of light 

in one direction or bi-directional when used as a threshold wingbar or siderow light with a red 
end light.  It is weatherproof and will endure roll over loads without damage.  The light fixture 
consists of a 1-piece aluminum optical assembly.  The aluminum optical assembly is mounted 
to a light base with six bolts and six 2-piece lock washers. The aluminum housing has a sand 
cast bottom cover that is attached using 6 screws.  A silicone o-ring is used to provide a 
watertight seal between the inner cover and the optical housing.  The lamp(s) are secured to an 
installed bracket, which is fastened to the bottom housing using vibration isolators.  Electrical 
connections are made at one or two feed-thru assemblies in the inner cover.  The feed-thru has 
an ITS verified L-823 plug for connecting to FAA L-830/ L-831 Isolation Transformers.  The 
outer lens is held into the aluminum housing with a bracket, gasket, molded elastomeric boot 
and 2 screws.  The light beam color is obtained by coloring the lens to the appropriate color 
for the application.  All hardware is type 18-8 stainless steel.  The complete light unit is 11.94 
inches in diameter, 5.13 inches deep, and weighs 16 lbs

 
 

 

CAUTION

 

 

CAUTION: 

Never handle the light assembly by the leads as this can break the 

waterproof seal. 

Содержание Crouse-Hinds 8506A-CS-P1




















Отзывы: