background image

Assembly

1. Reassemble valve parts 

with new o-rings on 
plugs (See figure 9).

Piston

Valve S/A

O-ring 

O-ring

Piston, Guide Spring

Spring, Compression

Fitting

Fitting

Figure 9

Check all mating surfaces.  Replace any parts that have scratches or burrs that could cause leakage.  Clean all metal parts in
clean solvent. Blow dry with air.  Do not wipe dry with cloth or paper towel because lint or other matter can get into the
hydraulic system and cause damage.  Do not use grit paper or file or grind these parts.

Note:

Lubricate all seals with clean petroleum jelly.  A good service policy is to replace all old seals with new seals.  Do not

use excessive lubricant on seals for meter section.

Refer to parts lists covering your steering control unit when ordering replacement parts.

Assembly Cleanliness

Recommendations

10

EATON Hydraulics  

Series 10 VersaSteer Parts and Repair  October 2004

Disassembly

24. Disassemble valve sub-assembly as

shown in figure 8.

Piston

Valve S/A

O-ring 

O-ring

Piston, Guide Spring

Spring, Compression

Fitting

Fitting

Figure 8

1/4” Hex Key

*Note:  The fittings included in the 

valve assembly are critical in 
the operation of the valve, 
and must not be switched 
with another style.

Torque Fittings to
31-45Nm [23-33 lb-ft]

Содержание Char-Lynn VersaSteer 10 Series

















Отзывы: