Eaton 9PX 5000 Скачать руководство пользователя страница 38

Страница: 38 / 44

Page 38

5-6kVA EU_EN

8. Troubleshooting

Power overload

Power requirements exceed the

UPS capacity (greater than

100% of nominal; see in table 6

on page 41 for specific output

overload ranges).

Remove some of the equipment from

the UPS.
The UPS continues to operate, but

may switch to Bypass mode or shut

down if the load increases.
The alarm resets when the condition

becomes inactive.

LED is On.
Beep continuous.

UPS overtemperature

The UPS internal temperature is

too high or a fan has failed.
At the warning level, the UPS

generates the alarm but remains

in the current operating state.
If the temperature rises another

10°C, the UPS transfers to Bypass

mode or shuts down if Bypass is

unusable.

If the UPS transferred to Bypass

mode, the UPS will return to normal

operation when the temperature drops

5°C below the warning level.
If the condition persists, shut down

the UPS.

Clear vents and remove any heat

sources. Allow the UPS to cool.

Ensure the airflow around the UPS is

not restricted. Restart the UPS.
If the condition continues to persist,

contact your service representative.

LED is On.
1 beep every 3 seconds.

The UPS does not start.

The input source is not connected

correctly.

Check the input connections.

The Remote Power Off (RPO)

switch is active or the RPO

connector is missing.

If the UPS Status menu displays the

"Remote Power Off" notice, inactivate

the RPO input.

Input bad wiring /

Output bad wiring

Input/Output cables are not

connected to the correct terminal

blocks.

Connect correctly the Input/Output

cables.

Led is On.
Beep continuous.
MBP disconnected

The HotSwap MBP is no more

connected to the UPS.

If the HotSwap MBP is connected

to the UPS, check that the detection

connector is correctly plugged.

Содержание 9PX 5000













































Результаты поиска

Содержание 9PX 5000

Отзывы:

Похожие инструкции для 9PX 5000

Бренды по названию

Популярные бренды

Eaton 9PX 5000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 9PX 5000

Отзывы:

Похожие инструкции для 9PX 5000

Бренды по названию

Популярные бренды