Eaton 150 DHP Скачать руководство пользователя

Страница: 24 / 26

Instruction Book

IB182217EN October 2018 www.eaton.com

50 / 75 / 150 DHP [Cable or Hard Bus Application]

Ground and Test Device

SECTION 6: INSPECTION AND
MAINTENANCE

6.1 INTRODUCTION

WARNING

DO NOT WORK ON A GROUND AND TEST DEVICE IN THE “CONNECTED”

POSITION.

DO NOT DEFEAT ANY SAFETY INTERLOCKS.

FAILURE TO FOLLOW ANY OF THESE INSTRUCTIONS MAY CAUSE DEATH,

SERIOUS BODILY INJURY, OR PROPERTY DAMAGE. SEE SECTION 2 -

SAFE PRACTICES FOR MORE INFORMATION.

6.2 FREQUENCY OF

INSPECTION

6.2 FREQUENCY OF INSPECTION

Inspect the ground and test device at least once a year or before

each use, especially in a severe service condition.

6.3 INSPECTION AND MAINTENANCE PROCEDURES

Insulation

Visually inspect all insulating barriers. Ensure that there is not

dirt visible on the surface of any of the barriers. If dirt is found,

clean with a lint-free cloth. If a solvent is required to cut dirt, used

Stoddard’s Solvent (Eaton part number 55812CA) or commercial

equivalent.

Hardware

Visually inspect all hardware. Replace any damaged or missing

hardware with parts equivalent to those provided with the ground

and test device.

Power Frequency Withstand Test

Individually energize each terminal (without cables, but with

insulating barriers) with the frame and device ground connection

system and all other terminals grounded. See Section 6-4 for

procedure.

6.4 INSULATION INTEGRITY CHECK

A sinusoidal AC voltage shall have a crest value of no less than 1.414

times the rated power frequency withstand voltage value specified,

and shall be applied to each terminal as specified in Section 6.3. The

frequency shall be /- 20% of the rated power frequency. For

5kV, the test voltage shall be gradually increased from zero to 15 kV

rms and held for 1 minute without flashover. For 7.5kV and 15kV, the

test voltage shall be gradually increased from zero to 27kV rms and

held for 1 minute without flashover.

Содержание 150 DHP



























Результаты поиска

Содержание 150 DHP

Отзывы:

Похожие инструкции для 150 DHP

Бренды по названию

Популярные бренды

Eaton 150 DHP, Инструкция

Результаты поиска

Содержание 150 DHP

Отзывы:

Похожие инструкции для 150 DHP

Бренды по названию

Популярные бренды