Easymount Single Hot EM-1600SH Скачать руководство пользователя страница 2

Страница: 2 / 20

Introduction

Thank you for purchasing the Easymount laminator.

Easymount is a high performance wide format mounting and laminating system with a

solid construction built to last.

The Easymount is great for mounting prints to boards and applying pressure sensitive laminates

as well as applying application tapes, double sided adhesives and vinyl’s.

The system is easy to use and much faster than squeegeeing by hand and is an ideal solution

to eliminating the hassles and expense of outsourcing.

Please read these instructions carefully before starting to use the system to ensure you

get the best results and are competent at operation.

Should you experience any problems please contact us and we will be happy to help. Call

us on:

0845 1 30 40 50

Содержание Single Hot EM-1600SH





















Результаты поиска

Содержание Single Hot EM-1600SH

Отзывы:

Похожие инструкции для Single Hot EM-1600SH

Бренды по названию

Популярные бренды

Easymount Single Hot EM-1600SH, Инструкция по эксплуатации товара

Результаты поиска

Содержание Single Hot EM-1600SH

Отзывы:

Похожие инструкции для Single Hot EM-1600SH

Бренды по названию

Популярные бренды