EN
Instructions
Customer Service / Importer:
DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany •
✆
+49 38851 314650 *)
*) Calls to German landlines are subject to charges. The cost varies depending on the service provider.
All rights reserved.
3
Items Supplied
1 x solar lamp
1 x ground spike
1 x remote control with 1 x 3 V button cell (CR2025), already
inserted
1 x instructions
Check the items supplied for completeness and transport dam-
age. If you
fi
nd any damage, do not use the product, but rather
contact the customer service department.
Remove any protective
fi
lm and labels.
Never remove the rating
plate!
Overview remote control
1 OFF
button
2 ON
button
3 FLASH
(
fl
ash function RGB + W
+ mixed colours)
4 STROBE
(
fl
ash function RGB)
5 FADE
(smooth change of colour)
RGB)
6 SMOOTH
(colour gradient RGB
+ W + mixed colours)
7
Control pad for colour selection
(12 mixed colours)
8
Setting RGB + W (Red, Green,
Blue, White)
9
Brightness setting
5
1
6
4
3
2
8
9
7
Changing the remote control battery
The battery is pre-installed. Only the transportation protec-
tion needs to be removed.
Before inserting the battery, check whether it is clean, and clean
it if necessary.
1. The battery compartment is located
on the narrow side of the remote
control. Remove it as shown.
2. Remove the empty battery and
insert a new battery (3 V, type
CR2025). The positive terminal
must point upwards.
3. Slide the battery compartment all the way back into the remote
control. It must audibly and noticeably lock into place.
Set-up
The solar lamp should not be placed near to other light sources
such as street lamps or other lamps, so that the LEDs can be
switched on automatically.
Position the solar lamp so that the solar
fi
eld is able to absorb
direct sunlight the whole day preferably.
Either place the solar lamp directly in position or secure it in place
using the ground spike.
1. Screw the ground spike into the receptacle on the bottom of
the solar lamp.
2. Push the ground spike into the ground.
Use
• The remote control only functions when the On / Off
switch on the bottom of the solar lamp is pressed.
• The individual colours and modes can also be set by
repeatedly pressing the On / Off switch (16 colours –
modes).
1.
Activation
– To switch the solar lamp on, press the On / Off
switch on the bottom.
The battery can now charge up in daylight. When darkness
sets in, the LEDs automatically switch on. When it gets light,
the LEDs switch off and the battery is charged up via the solar
fi
eld.
Please note:
Battery power can be severely impacted by ex-
tremely low temperatures.
2.
Selecting a colour
– Press the corresponding colour selection
button (
7, 9
) on the remote control or press the On / Off switch
on the solar lamp several times to switch between the different
colours.
3.
Setting the mode
– Press the corresponding mode button
(
3 – 6
) on the remote control or press the On / Off switch on
the solar lamp several times to switch between the different
modes.
4.
Setting the brightness
– Set the brightness via the
and
buttons (
9
).
5.
Turning LEDs on / off
– To turn the LEDs on or off, press the
ON
(
2
) or
OFF
button (
1
) on the remote control.
Please note:
The solar lamp remains in stand-by, so that the
storage battery can continue to charge during daylight.
6.
Deactivation
– To switch the solar lamp off, hold down the
On / Off switch on the bottom for approx. 3 seconds.
Technical Data
Power supply:
3,7 V DC (1x storage battery Li-Ion ICR18650,
1800 mAh)
Power:
max. 2 W
Charging time:
approx. 6 to 8 hours (in sunlight)
Lighting time:
up to 8 hours (with a fully charged storage
battery)
Type of
protection:
IP67
ID Instructions: Z 07810_07811 M DS V1 1118
Variations
Article number
Shape
Model number
07810
ball
SG9011
07811
stone
SG9025
Disposal
Dispose of the packaging material in an environmentally
friendly manner and take it to a recycling centre.
This product is governed by the European Direc-
tive 2012/19/EU on waste electrical and electronic
equipment (WEEE). Do not dispose of this product
as normal domestic waste, but rather in an environ-
mentally friendly manner via an of
fi
cially approved
waste disposal company.
The battery should be removed before the remote
control is disposed of and should be disposed of
separately from the remote control at suitable col-
lection points.
push
pull
Article number: 07810 / 07811