PANTONE 072 C
PANTONE 123 C
Customer service: 0871 855 6100
For more innovative products from Easylife please visit:
www.easylifegroup.com
If your steam mop begins to produce steam more slowly than usual or stops producing steam, you may
need to remove lime scale. Lime scale can develop over time on the metal parts and greatly affect the
mop performance.
It is necessary to remove lime scale on regular basis every 25-50 times you use a full tank of water or at
least once a month, especially in areas with hard water. The frequency of lime scale removal depends
upon the hardness of you tap water and how often you use the steam mop.
Using cleaning solution
1. Prepare a solution of 1/3 white vinegar and 2/3 tap water and add to the water tank.
2. Secure and position the unit to ensure steam released is aimed away from the floor or surrounding
objects and surface. Plug the unit in, turn the unit ON by pressing the power switch, and allow the unit to
produce steam unit the vinegar/water solution in used up.
3. Repeat the above procedure as many times as necessary unit a normal steam flow rate is achieved.
4. Fill the water tank with fresh water and rinse out thoroughly.
5. Fill the water tank with fresh water, attach to the unit and release steam through the system unit the
water tank is empty.
WARNING: Don’t leave the steamer unattended during the lime scale removal process and/or while
in use.
NOTICE: Preform a test clean on a suitable isolated area after each lime scale removal to ensure that
there is no debris left in the system.
Cleaning blocked steamer accessories
• Due to the high mineral content of water in some areas, you may notice that less steam comes out
from the Hand-Held steamer accessories. This may be caused by calcium build up inside the tip
of the nozzle. We recommend using a spray lubricant. Spray a small burst or two of the lubricant
inside the tip of the Jet nozzle. After spraying lubricant inside the component, till the steamer with
water according to the directions and run a continuous jet of steam through the affected accessory
for several minutes to remove the deposit once the steam pathway is clear , aim the steamer at a
neutral surface or cleaning cloth to make sure no debris is emitted.
• This product contains no serviceable parts. Do not try to repair it yourself. Any servicing that requires
disassembly other than cleaning must be performed by a qualified appliance repair technician.
ALL servicing should be done by an authorized service representative.
Cleaning Microfibre Floor Cleaner
Machine washable on “warm” setting. Always use a mild detergent. For best care results lay flat to dry.
IMPORTANT: Allow the steamer to fully cool down before performing any maintenance or
troubleshooting checks.
IMPORTANT: Never use bleach or fabric softener when washing the microfibre floor cleaner.
ASSEMBLY (continued)
5. When the water tank is full it will maintain steam for approximately 20 minutes. If the water tank is
low the indicator lights on the water tank will glow red and the lights will flash to point out you need
to add water.
6. Press the steam button (4) to activate the steam.
7. You can control the volume of steam by turning the steam control knob (12) Clockwise to increase
the amount of steam and anti-clockwise to reduce it.
Using the hand steam cleaner
Push the lock catch (6), remove the main body (A) out of holder.
Install the accessory adaptor of your choice at the top of main body (A) until it clicks into place (please
refer to the accessories table for the appropriate attachment.
For the following attachments it is necessary to use the accessory adapter (F) to connect these:
Insert the accessory adapter (F) to the main body (A) by pushing firmly so the two parts connect
together. In order to connect the accessory attachment to the accessory adapter simply push and turn
clockwise to lock into place. In order to remove simply turn anti-clockwise.
Small and medium scrub brushes (D&E), Angle Nozzle (G), Grout Cleaning Tool (H) and Scraping Tool
(I), see Fig 5 below.
CLEANING AND MAINTENANCE
YOUR WARRANTY WILL BE VOID IF THIS IS IGNORED:
In areas of hard water it is recommended that distilled water is used. Hard water will immediately
reduce the performance of your Steam Mop and prolonged use will cause permanent damage to
the mechanism, rendering it un-useable. This will render your warranty void. Any Steam Mop
returned will be thoroughly checked by our technicians for compliance.
PLEASE MAKE SURE THAT THE APPLIANCE IS DISCONNECTED FROM THE MAINS POWER
OUTLET WHEN CLEANING THE MOP AND ACCESSORIES. DRAIN ANY REMAINING WATER IN
THE TANK AND CLEAN THE TANK AFTER EVERY USE.
Please use detergent to clean the accessories (Jet Nozzle and Round Brush) when they are dirty then
wash with clean water and dry
How to descale the Water Tank
To clean calcium deposits / lime scale that builds up inside the water tank, add one or two tablespoons
of white vinegar to a full water tank. Close the water tank cap and then shake the contents. DO NOT
TURN THE STEAMER ON.
FIG. 5
