Eastwood 58878 Скачать руководство пользователя страница 3

To order parts and supplies: 800.343.9353  >>  eastwood.com 

3

  

READ ALL SAFETY WARNINGS AND  

   

 

  ALL INSTRUCTIONS!

Failure to follow the warnings and instructions may result in electric shock,  
fire and/or serious injury.

Save all warnings and instructions for future reference.

 

SERIOUS INJURY, FIRE,  

 

 

 AND EXPLOSION HAZARDS!

•  Keep Dry – 

DO NOT

 operate or store in damp or wet conditions.

• 

DO NOT

 drop, short circuit, incinerate, expose to temperatures greater than 

140°F [60°C].

•  No user serviceable parts inside – 

DO NOT

 open tool.

• 

DO NOT

 attempt to charge or use this tool if damaged.

• 

DO NOT

 operate in explosive atmospheres such as explosive vapors,  

flammable liquids, gasses, or dust.

•  Not a toy. Keep out of the reach of children.
•  Charge tool only according to these instructions.
• 

DO NOT

 use any chargers other than the one specifically supplied with  

this tool.

 

HEALTH HAZARD!

•  Dust and fine particles are generated while grinding which can contain 

hazardous or toxic substances. Breathing this dust can cause many seri-
ous respiratory health conditions. Always use NIOSH approved respiratory 
protection while using this Grinder.

 

EYE INJURY HAZARD!

•  Rapidly moving abrasive surfaces can eject metal particles, dirt and debris 

at high velocity. Always wear ANSI approved eye protection when operating 
this tool.

SAFETY INFORMATION

WARNING! LITHIUM BATTERIES STORE A LARGE AMOUNT OF ENERGY AND WILL 

ERUPT IN FLAMES OR VIOLENTLY EXPLODE IF NOT PROPERLY HANDLED.

Содержание 58878













Отзывы: