Eastwood 22979 Скачать руководство пользователя страница 4

4

 

Eastwood Technical Assistance: 800.343.9353  >>  [email protected]

 

 READ INSTRUCTIONS 

•  Thoroughly read and understand these product instructions before using the Sander.
•  Keep these product instructions for future reference.

 

HEALTH HAZARD!

•  Dust and fine particles are generated while sanding or grinding which can contain hazardous or toxic substances. Breathing this dust can  

cause serious respiratory health conditions. Always use NIOSH approved respiratory protection while using this Sander.

•  This Sander will eject particles, dust and sparks at high velocity during operation. Wear approved eye and skin protection at all times  

while operating.

•  Sanding or grinding with this Sander can generate excessive noise. Wear appropriate hearing protection while using.

 

INJURY HAZARD!

•  The moving Belt or rotating Disc of this Sander can quickly catch loose clothing, long hair or jewelry causing serious personal injury.  

Keep all loose clothing, long hair and jewelry away when operating Sander.

•  This Sander can quickly start up when handling while plugged in to electrical supply causing serious personal injury.  

Always unplug the tool from the electrical supply before changing Sandpaper, making adjustments to the tool or performing maintenance.

•  Moving abrasive surfaces can quickly abrade skin. Keep hands and fingers away from moving abrasives.
•  This Sander can quickly and violently propel workpiece objects while operating causing injury and or property damage. Do not apply excessive 

force to Sander while in use. Always make sure the workpiece or material being cut is held securely and work is done only on the left side  
of the Disc.

•  If excessive vibration is felt, discontinue use immediately and disconnect tool from electrical supply. Inspect abrasive Platen or components  

for damage. Do not resume use until resolution is found.

 

FIRE HAZARD!

•  This Sander will eject a trail of sparks at high speed which can ignite flammable materials or injure others nearby. Do not operate in the vicinity  

of flammable materials and keep all persons and pets away from the work area.

ADDITIONAL SAFETY INFORMATION

Содержание 22979









Отзывы: