Eastwood 21301 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 20

Eastwood 21301 Скачать руководство пользователя страница 12

12

Eastwood Technical Assistance: 800.343.9353 >> [email protected]

FIG. 20

INSTALL VACUUM/FILTER ASSEMBLY TO CABINET (K TO A)
NOTE:

The Vacuum/Filter Assembly is moderately heavy, and it is

best to remove the Motor and Filter before installing on the Cabi-
net. Also, the assistance of a capable helper is necessary.

• Place the Vacuum/Filter Assembly on the floor and unlatch

the 2 Clasps.

• Pull the Motor & Filter out of the top of the Housing and set

it aside.

• With the assistance of a helper, align the mounting holes of

the brackets with the 4 holes at the upper back wall of the
Cabinet. Secure it in place using 4 sets of M6 Screws and
Nuts

(FIG 20)

.

• Carefully lower the Motor/Filter Assembly back into the

mounted Housing and latch the Clasps securely

(FIG 21)

.

• Connect the Plug on the power supply cord with the

female Receptacle on the cord attached to the Light
Fixture

(FIG 22)

.

• The Eastwood Abrasive Media Blast Cabinet is now fully

assembled and ready for set-up.

FIG. 21

FIG. 22

«
...
10
11
12
13
14
...
»

Содержание 21301





















Отзывы:

Нет отзывов