Eastey EC Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 39

Eastey EC Series Скачать руководство пользователя страница 17

Installation 17

Mounting the Ink Jet Printer

There are mounting holes predrilled that allow you to mount a variety of printing

systems on the Variable-Speed Conveyor.

Refer to the User Guide that came with

your printer for mounting instructions.

The illustrations that follow in this section show examples of possible locations for

attaching mounting brackets for some common printer configurations. Your printer

configuration may be different.

Example of Variable Speed Conveyor with CoPilot Mounting Bracket

A pre-drilled and tapped mounting Bracket Support Plate is provided for installation of

the Printer Mounting Bracket. Use four (4) ¼-20 × 1” hex-head bolts with flat washers

and lock nuts to fasten the Baseplate Connector Clamp to the Bracket Support Plate.

Note

The above example shows a CoPilot Max system on 2005061

kit. Other printers can be mounted in a similar way.

Note

Threaded holes in the conveyor side plates are provided on

both sides of the conveyor for mounting Guide Rail mounting

rod brackets.

CoPilot

Controller

CoPilot

Print Head

Printer

Mounting

Bracket

Baseplate

Connector

Clamp

Bracket

Support

Plate

Pairs of holes

pre-drilled and

tapped for Guide

Rail mounting

rod brackets

«
...
15
16
17
18
19
...
»

Содержание EC Series








































Отзывы:

Нет отзывов