East Coast Datacom PDS-1/10G Скачать руководство пользователя страница 2

PDS-1/10G Portable Delay Simulator Chassis User's Manual

2

 

 

 

 

 

 
 

SAFETY WARNING 

 

Always observe standard safety precautions during installation, operation and maintenance of this 
product.  To avoid the possibility of electrical shock, be sure to disconnect the power cord from the 
power source before you remove the IEC power fuses or perform any repairs. 

 

 

PROPRIETARY NOTICE 

 

The information contained herein is proprietary to East Coast Datacom, Inc.  Any reproduction or 
redistribution of this publication, in whole or in part, is expressly prohibited unless written 
authorization is provided by East Coast Datacom, Inc. 

 
 
 

WARRANTY NOTICE

 

 

WARRANTIES:  East Coast Datacom, Inc. (hereafter referred to as E.C.D.) warrants that its 
equipment is free from any defects in materials and workmanship.  The warranty period shall be 
three (3) years from the date of shipment.  E.C.D.'s sole obligation under its warranty is limited to 
the repair or replacement of defective equipment, provided it is returned to E.C.D., transportation 
prepaid, within a reasonable period.  This warranty will not extend to equipment subjected to 
accident, misuse, alterations or repair not made by E.C.D. or authorized by E.C.D. in writing. 

 
 
 

PUBLICATION NOTICE

 

 

This manual has been compiled and checked for accuracy.  The information in this manual does 
not constitute a warranty of performance.  E.C.D. reserves the right to revise this publication  and 
make changes from time to time in the content thereof.  E.C.D. assumes no liability for losses 
incurred as a result of out-of-date or incorrect information contained in this manual. 
 
 
 
 
 
 
 
 
 

Содержание PDS-1/10G




















Отзывы: