background image

Remove spreader and components from carton 
and place spreader upside down. Slide drive and 
free wheels on axle as shown with the longer por- 

tion of wheel hub facing the frame. Secure free wheel with  
a 5/32 Dia. x 1 1/4” cotter pin. Secure drive wheel to axle with 
3/16” Dia. x 2” cotter pin. Attach leg to frame as shown with (4) 
1/4-20 x 2 1/4” hex bolts, lockwashers, and nuts. Tighten 
securely. 

assembly to brace (make sure on/off lever is positioned as shown)  
using (4) 1/4-20 x 1 1/2” hex bolts, lockwashers, and nuts. Tighten 
securely. Install handle grips onto upper handle.

 

                               

Turn spreader upright on wheels and 
insert screen into hopper. Attach 
lower handle brace to the outside of 

frame with (4) 1/4-20 x 5/8” hex bolts, 
lockwashers, and hex nuts. 

Do not tighten 

bolts. 

Attach upper handle                 

Slide handle lever between lever brackets as shown and 
secure with 

1/4 Dia. clevis pin and 3/32 Dia. x 5/8” 

cotter pin.

 I

nstall on/off control tube to control lever 

using 1/4 Dia. clevis pin and 3/32 Dia. x 5/8” cotter pin.
Remove tape holding the lower rod to the pivot 
lever and slide opposite end of control tube onto 
lower control rod. Secure with a 3/32 Dia. cotter pin. 

TIGHTEN ALL NUTS AND BOLTS LEFT LOOSE IN 
STEP #2. 

BF 1 STAINLESS MODEL ONLY

-Attach trim 

control lever to the upper handle using (2) #10-24 x 2 
1/4” screws and locknuts. Secure control cable to 

lower brace with the plastic cable tie. 

 

To check spreader for  complete shutoff, pull the on/off control lever back to the “OFF” position. Determine if the 
port holes are completely closed. If they are not, loosen the brace/frame bolts and push down on the handle 
and front of spreader. Re-tighten bolts and check shutoff. 

Trim 

Control 

Lever 

#10-24 x 2 1/4” 

Screws and 

Locknuts 

Control Cable secure to lower 

brace w/ plastic 

cable tie 

LOWER HANDLE BRACE 

Attach to frame with 

(4) 1/4-20 x 5/8” hex 

bolts, lockwashers, and 

nuts 

 

UPPER HANDLE 

ASSEMBLY 

Attach to brace with 

(4) 1/4-20 x 1 1/2” hex 

bolts, lockwashers,  

and nuts 

 

ON/OFF LEVER 

SCREEN 

Insert into hopper 

 HOPPER 

 FREE 

  WHEEL 

 

5/32 Dia. x 1 1/4” 

COTTER PIN 

3/16 Dia. x 2” 

COTTER PIN 

 DRIVE 

 WHEEL 

 

Opposite end of Control 

Tube slides onto lower 

rod and is secured w/ 

3/32 Dia. cotter pin 

 CONTROL 

TUBE 

 

 Control Tube- attached 

 with 1/4 Dia. clevis pin 

 and  3/32 Dia. cotter pin 

ASSEMBLY 

LEG  

Attach to frame with 

(4) 1/4-20 x 2 1/4” hex 

bolts, lockwashers, and 

nuts 

 Handle Lever– attach 

 with 1/4 Dia. clevis pin 

 and  3/32 Dia. cotter pin 

Handle 

Lever 

 

Содержание Prizelawn BF l









Отзывы: