background image

1-800-345-6007

Page 10

www.ardisam.com

To prevent accidental starting:
Avoid injury! Engine must be turned off and cool,
and spark plug wire must be removed from spark plug
before checking and adjusting engine or equipment.

 

CAUTION

Avoid injury! Engine must be shut-off, cool, and spark
plug wire removed before any repair or maintenance
can be done.

 

CAUTION

Avoid injury! Temperature of muffler and nearby
areas may exceed 150° F (65° C). Avoid these areas.

 

CAUTION

Avoid injury! Check mini cultivator often for loose
nuts and bolts. Keep these items tightened.

 

 

CAUTION

Cooling Fins

Cooling fins, air inlets and linkages must be free from

any debris before each use.

Air Filters

Never run engine without air cleaner properly installed.

Added wear and engine failure may occur if air cleaner is
not installed on engine.

Service air cleaner every 3 months of operation. Clean

and oil filter daily in extremely dusty conditions.

Steps for Cleaning Air Filters

1.

Wash in warm water with mild soap until dirt and debris

are removed. Press filter when washing, do not twist.

2.

Rinse in warm water until soap and dirt are removed.

3.

Dry filter by wrapping in a clean cloth and pressing filter

until it is dry.

4.

Apply oil to the entire filter.

5.

Remove excess oil by squeezing filter.

6.

Attach the filter and filter cover to the engine.

Spark Plug

Check spark plug at the beginning of each season.

1.

Remove dirt and debris around the spark plug before

removing.

2.

Remove spark plug and replace if any of the following

have occurred: pitted electrodes, burned electrodes,
cracked porcelain, or deposits around the electrodes.

3.

Check spark plug for proper gap (.025” to .030”).

4.

After analysis of the spark plug, install original or a new

spark plug and tighten securely.

NOTE: DO NOT OVERTIGHTEN!

NOTE: SPARK PLUG IS NGK BM6A OR CHAMPION CJ8.

Carburetor

Never tamper with factory setting of the carburetor.

MAINTENANCE AND ST

MAINTENANCE AND ST

MAINTENANCE AND ST

MAINTENANCE AND ST

MAINTENANCE AND STORAGE

ORAGE

ORAGE

ORAGE

ORAGE

Mini Cultivator Maintenance

Mini Cultivator Maintenance

Mini Cultivator Maintenance

Mini Cultivator Maintenance

Mini Cultivator Maintenance

1.

The transmission case has 1.5 oz. or (3 tbsp.) of

grease installed at the factory. It is recommended that once
a year the transmission case be split and the grease level
checked. A high quality lithium grease is recommended,
which can be purchased at most automotive and hardware
stores. DO NOT overfill.

2.

Keep all screws, nuts, and bolts tight.

3.

For cold weather operation, store the unit in a cool

environment. Transferring the unit from a warm to a cold
place can cause the build up of harmful condensation.

Engine Maintenance

Engine Maintenance

Engine Maintenance

Engine Maintenance

Engine Maintenance

Avoid injury! Never store engine with fuel in the tank
inside a building. Potential sparks may be present
for ignition of fuel and fuel vapors.

 

 

CAUTION

Avoid injury! An adult must always do maintenance
and repair on engine and mini cultivator.

 

 

CAUTION

Never twist air filters when cleaning. Always press.

Содержание MC43E





















Отзывы: