EarthCore Isokern MAXIMUS 2L48 Скачать руководство пользователя

Страница: 47 / 58

Earthcore Industries

01/2020

Isokern Maximus Linear Series Gas Fireplace

Burner Installation

Connect all burner segments according to burner model diagram Page 55. Make sure all connections are tightly secured.

Place burner assembly in center of fireplace floor or cavity.

Rotate the burner to position the gas inlet fitting on burner closest to the gas-supply stub coming from the gas valve. (Not

necessary for models ISF72/96LB)

Remove the burner top closest to the gas-supply stub. Remove the top pan by unscrewing the two screws. This will allow

easier access and connection of flex connector to the flared fitting.

Connect the 12” flex connector to the gas inlet flared fitting on the burner assembly.

Remove the cap on gas-supply stub and install the appropriate size flared fitting female adapter.

Connect the other end of 12” flex connector to the gas-supply female adapter. Avoid creating kinks in the flex connector.

Make sure all connections are tightly secured.

Place the removed burner top back on to the orifice block and secure tightly with the pan head screws.

10.

Check appliance operation. Turn on burner then observe the individual tongues of flame on the burner. Make sure all

ports are open and producing flame evenly across the burner. If any ports are blocked, or partially blocked, clean out the

ports. With gas line installed, run initial system checkout before steps 13 - 15.

11.

Pour glass media on to burner top pan tray.

12.

Spread media evenly across hearth floor and pan tray, avoid covering burner ports with excess media. Do not fill burner

cavity with glass media or any other material.

13.

Optional gas logs available, shown on page 56.

VALVE CONTROL

BOX

BURNER

(ISF36LB SHOWN)

BURNER

CAVITY

SEE DETAIL

VALVE

CONTROL BOX

SEE

DETAIL

BURNER

(

ISF72LB SHOWN)

BURNER

CAVITY

3/8" Hard pipe must extend 3" from

sidewall for models: ISF24/36/48LB
OR
within 3" from center of burner cavity
for models: ISF72/96LB MODELS.

PILOT

ASSEMBLY

VALVE CONTROL

BOX

BURNER

(ISF36LB SHOWN)

BURNER

CAVITY

SEE DETAIL

VALVE

CONTROL BOX

SEE

DETAIL

BURNER

(

ISF72LB SHOWN)

BURNER

CAVITY

3/8" Hard pipe must extend 3" from

sidewall for models: ISF24/36/48LB
OR
within 3" from center of burner cavity
for models: ISF72/96LB MODELS.

PILOT

ASSEMBLY

FIGURE 40

Содержание Isokern MAXIMUS 2L48



























































Результаты поиска

Содержание Isokern MAXIMUS 2L48

Отзывы:

Похожие инструкции для Isokern MAXIMUS 2L48

Бренды по названию

Популярные бренды

EarthCore Isokern MAXIMUS 2L48, Инструкция по установке, эксплуатации, обслуживанию и руководство владельца

Результаты поиска

Содержание Isokern MAXIMUS 2L48

Отзывы:

Похожие инструкции для Isokern MAXIMUS 2L48

Бренды по названию

Популярные бренды