4
• Never under any circumstances aim the Spray
Gun at another person or animal. In the event
of injury occurring seek expert medical advice
immediately.
• The Spray Gun must only be used with paints
and solvents that have a flash point suitable
for spraying. If in doubt, consult the paint or
solvent manufacturer’s data.
• Always ensure there is adequate ventilation
when spraying.
• NEVER spray near a naked flame, including
appliance pilot flame.
• NEVER smoke whilst spraying.
• NEVER allow children to operate or play with
the Spray Gun.
• Always read the solvent manufacturer’s
instructions before use.
• Always disconnect unit from mains supply
when filling the paint container.
• Always wear a suitable protective mask when
spraying. We also recommend the use of
gloves, goggles and overalls.
• After each use, thoroughly clean the Spray
Gun.
• This appliance is not intended for use by
>
persons (including children) with reduced
>
physical, sensory or mental capabilities or lack
>
of experience and knowledge, unless they
>
have been given supervision or instruction
>
concerning use of the appliance by a person
>
responsible for their safety.
• Use only genuine manufacturer replacement
parts.
• Always disconnect the SprayStation from the
mains supply before cleaning the appliance.
• If the supply cord is damaged, it must be
replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid
a hazard.
•
WARNING!
The use of any accessory or
attachment, other than those recommended in
this instruction manual, may present a risk of
personal injury.
• Use the Spray Gun for the job it was designed
for only. Mis-use of the Spray Gun will
invalidate the guarantee.
• Wear ear protection.
WARNING! The substances used with this
Spray Gun (paints, solvents, etc.) may
contain dangerous, harmful, explosive or
corrosive materials. ALWAYS COMPLY WITH
THE SAFETY INSTRUCTIONS ISSUED WITH
THIS PRODUCT AND THE MATERIAL BEING
USED.
No.
Description
Part Code
1.
Needle and Fluid Tip Tool
V0018
2.
Air Cap Ring
V0001
3.
Air Cap
V0002
4.
Spray Direction Plate
V0003
5.
Fluid Tip 2.0mm
V0004
6.
Fluid Tip O-Ring
V0005
7.
Needle 2.0mm
V0006
No.
Description
Part Code
8.
Lip Seal - Fluid Needle
V0007
9.
Paint Flow Adjuster
V0011
10.
Paint Container Seal
L0682
11.
Pick-Up Tube
V0012
12.
Paint Container
V0014
12a.
Paint Stirrer
L1565
17.
Viscosity Cup
SG243
The concept
A motor feeds out a high volume of air (HV) and enables products to be sprayed at a low pressure (LP). The Air Hose (13) feeds the air produced by
the motor to the Spray Gun. The solution is released from the Fluid Tip of the Spray Gun at a very low pressure and is enclosed in a high volume of
air.
The powerful motor can spray a wide range of solutions with or without dilution. However, there will always be some which will not be suitable for
the Spray Gun. Good quality paint contains a high percentage of solids which make the dilution easier. The users must keep in mind that low
temperatures make the paint thicker, that’s why we recommend spraying with the Spray Gun at a 15°C minimum temperature.
No.
Description
Part Code
13.
Air Hose
L1064
14.
Filter
L0058
No.
Description
Part Code
15.
Air Hose
L0896
16.
Filter
L0290
PARTS LIST
FIG.1
PARTS LIST HV3500
FIG.2
PARTS LIST
HV2900/3900KR/5900
FIG.3
SAFETY OPERATING INSTRUCTIONS
PLEASE READ BEFORE USE
INTRODUCTION
Содержание SprayStation HV3900KR
